manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 197

CONVENIENCE DEVICES

11-17

DVD Navigation Unit*

Location of Navigation Unit

The navigation unit is installed behind
the rear left side cover.

DVD Changer*

CD Changer*

CD/DVD changer is installed in the center console.

How to change a CD or DVD

1. Open the lower cover in center console.

2. Slide the changer cover to direction  .

3. Press the opening button  . CD/DVD case appears within few seconds.

4. Remove the CD/DVD case from the changer.

5. Insert a CD/DVD into the case and put the case back into the changer.

6. When pressing the case down, it is automatically moved down.

7. Close the changer cover and lower cover in center console.

Use only a navigation map DVD.

CAUTION

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands