SSANGYONG RODIUS 2006 Owner'S Manual Download Page 171

Page: 171 / 286

VENTILATION, HEATING, AIR CONDITIONING AND AIR PURIFICATION SYSTEM

9-15

DEFOGGING AND DEFROSTING

Inside

1. Press the defroster switch.

2. Adjust the fan speed with the fan speed control speed.

3. To quickly remove the fog on the glass, set the switch at

high speed position.

4. To prevent the fog generating on the glass, setting the air

source selection switch to the fresh air intake mode is
recommended.

Defroster switch

Automatic air conditioner

Manual air conditioner

Outside

1. Press the defroster switch.

2. Adjust the fan speed with the fan speed control speed.

3. To quickly remove the fog on the glass, set the switch to

high speed position.

4. Set the temperature control switch to hot position.

When you press this switch, the air conditioner turns on automati-
cally and the system selects the fresh air intake mode.

NOTE

• To prevent the fog generating on the glass, setting the air source

selection switch to the fresh air intake mode is recommended.

• An extended air conditioner operation in bi-level mode or defrost

mode may cause the fogged outside glass due to high tempera-
ture difference between inside and outside of the vehicle. In this
case, change the air flow to vent mode and use the low fan speed.

• Especially in winter and summer, to avoid glass fogging, remove

any obstacles such as snow or leaves on the air inlets.

CAUTION

Summary of Contents for RODIUS 2006































































































































































































































































































Search results

Summary of Contents for RODIUS 2006

Reviews:

Brands by name

Popular brands

SSANGYONG RODIUS 2006, Owner'S Manual

Search results

Summary of Contents for RODIUS 2006

Reviews:

Brands by name

Popular brands