Home
/
SSANGYONG
/
RODIUS 2006
/
Owner'S Manual

SSANGYONG RODIUS 2006, Owner'S Manual

Share

Page: 136 / 286

SSANGYONG RODIUS 2006 Owner'S Manual Download Page 136

SEATS

7-18

HOW TO REMOVE AND INSTALL THE THIRD ROW SEAT (7-SEATERS)*

1. Fold down the seatback of the third row seat while puling

up the seatback reclining lever ( ).

2. Remove the seat rail covers ( )

3. Slide the third row seat to its rear end (arrow direction) while

pulling up the seat sliding lever ( ).

4. Carefully remove the third row seat from the rail by using

the hand grips ( ,

) on the seat as shown in the figure.

5. Install the seat in the reverse order of removal.

• Be careful not to drop the seat when removing it. It may cause

apersonal injury.

• Make sure that the seat is securely engaged on the rail

duringinstallation.

• Do not put any luggage between the 2nd and 3rd row if the 3rdrow

seat has been removed and the 2nd row seat is rotated. It may
cause serious personal injury when the brake is applied suddenly.
Please put the luggage only when the seat is installed in normal
position.

CAUTION

«
...
134
135
136
137
138
...
»

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands