manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 75

INTERIOR SWITCHES

4 - 2 7

Electronic Compass

NW

SE

W

S

E

S W

N E

N

It indicates 8-direction by interval of 45°
according to the vehicle’s driving direction.
This is available only when the vehicle
speed is over 2.8 km/h.

Turning Calibration

When the multimeter is installed to the vehicle or the battery
is replaced, you have to perform calibration by circulating your
vehicle. If not, there will be misreading in direction.

1. If you press the MODE and UP button simultaneously for

more than 1 second, the current direction flashes.

2. Turn the vehicle over 1 complete circle within 128 seconds

slowly, then the calibration will be accomplished.

3. When the calibration is finished, the vehicle’s new direction

will be indicated.

The direction will be indicated while driving.

NOTE

• You can turn to any direction, left or right.

• When the calibration is completed, the compass does not flash

anymore.

• If the compass continues to flash, turn again slowly until it goes off.

NOTE

Release conditions for turning calibration

• When the MODE and UP button simultaneously are pressed

briefly.

• When the vehicle is not turned within 128 seconds after

calibration mode started.

Electronic
Compass

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands