manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 18

SAFETY PRECAUTIONS

1-2

CHECKS BEFORE STARTING A JOURNEY

CHECK THE VEHICLE OUTSIDE

1. Check the tyre inflation and wear.

2. Check the engine oil level and other fluid/oil levels in

engine compartment.

3. Clean the windshield glass, rear glass, and side

mirrors.

4. Make sure that the engine hood and tailgate are prop-

erly closed.

5. Make sure that there are no obstacles in the danger area

around the vehicle.

CHECKS BEFORE STARTING A JOURNEY

CHECK THE VEHICLE INSIDE

1. Make sure that all doors including tailgate are properly

closed.

2. Adjust the driver’s seat for comfortable driving.

3. Adjust the outside and inside rear view mirrors.

4. Fasten the seat belts and be sure that all other occu-

pants have fastened theirs properly.

5. Check the parking brake operations.

6. Check that all appropriate warning lights are operating

when turning the ignition key to the “ON” position.

7. Check the operations of clutch pedal, accelerator pedal,

and brake pedal.

8. Make sure that there are no obstacles in the danger area

around the vehicle.

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands