Home
/
SSANGYONG
/
RODIUS 2006
/
Owner'S Manual

SSANGYONG RODIUS 2006, Owner'S Manual

Share

Page: 92 / 286

SSANGYONG RODIUS 2006 Owner'S Manual Download Page 92

INSTRUMENT PANEL

5-12

ESP Warning Light*

If you press the ESP OFF switch, the ESP
function stops and the indicator lamp in in-
strument panel comes on.

Press this switch again to resume the ESP function.
At this time, the indicator lamp goes out.

If the ESP function operates while driving, the indicator lamp
flickers and the alarm sounds.

If the ESP warning light comes on, the ESP related system is defective.
At this moment, the ABS works in a basic way. However, make
sure to check the vehicle at the nearest Ssangyong Dealer or
Ssangyong Authorized Service Operation.

CAUTION

EBD Warning Light

This warning light comes on when the igni-
tion switch is turned to ON and should go
out if the system is normal. If the EBD sys-

tem is abnormal, both EBD warning light and ABS warning
light come on simultaneously.

If the warning light stays on, have the system checked by Ssangyong
Dealer or Ssangyong Authorized Service Operation.

WARNING

«
...
90
91
92
93
94
...
»

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands