manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 203

IN CASE OF EMERGENCY

12-3

7. Connect one end of the second lead of jumper cable to

the negative terminal of the booster battery.

8. Make the last connection to a suitable ground, such as a

steel bracket bolted to the engine block. This last connec-
tion should be as far away from the battery as possible.

9. Attempt to start the engine with discharged battery while

slightly accelerating the engine with booster battery.

10. If the engine is started, let it run for a few minutes.

11. After starting the engine, carefully disconnect the jumper

cables in the reverse sequence of connection.

• Connecting the jumper cable to the negative terminal of the dis-

charged battery could result in arcing and possibly a battery
explosion. Serious personal injury or vehicle damage can result.

• Make sure that the jumper leads are securely connected. Otherwise,

an abrupt disconnection due to vibration during engine starting may
cause an electrical short resulting in severe damage in electric
components.

• Make sure that the booster battery has the same voltage rate with

the discharged battery.

Batteries can explode. You could be burned by battery acid. Electrical
short could injure you or damage the vehicles.

• Do not expose battery to flames or sparks.

• Do not allow cable terminals to touch each other.

• Do not allow battery fluid to contact eyes, skin, fabric, or painted

surfaces.

• Do not disconnect discharged battery from vehicle.

• This can create damage to electrical systems in both vehicles, and

cause serious personal injury.

WARNING

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands