manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 244

SERVICE AND MAINTENANCE

13-20

Use only the fuse with same rating.

Normal

FUSE REPLACEMENT

1. Turn off all electrical equipment and set the ignition switch

to “LOCK”.

2. Locate the defective fuse. Refer to the fuse label in this

manual.

3. Open the fuse and relay box cover.

4. Pull out the relevant fuse by using the fuse puller.

5. Visually check whether it is blown off or not.

6. If normal, insert it to its original position.

7. If blown, check its capacity and replace it with the same

capacity.

Blown

The underhood fuse and relay box has some spare fuses. Refill the
fuses immediately as you use them. The fuse rating is indicated on
the upper surface of the fuse.

NOTE

If you remove the fuse when the electrical power is supplying, the elec-
trical equipment could be damaged. Replace the fuse when the ignition
key is in "LOCK" position.

CAUTION

The use of different types or different rating fuses could cause dam-
age to the electrical system and even start a fire.

• Always replace fuse with one with the same rating.

• Never use anything else but a fuse.

• Do not use anything metal to remove fuse.

WARNING

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands