Home
/
SSANGYONG
/
RODIUS 2006
/
Owner'S Manual

SSANGYONG RODIUS 2006, Owner'S Manual

Share

Page: 248 / 286

SSANGYONG RODIUS 2006 Owner'S Manual Download Page 248

SERVICE AND MAINTENANCE

13-24

WIPER BLADE REPLACEMENT

1. Lift the wiper arm up from the

windshield.

3. Slide the blade down and remove it

from the arm.

4. Install a new blade.

5. Put the wiper arm down to its park-

ing position.

Front wipers

Rear wiper

2. Press the safety button ( ).

• Do not open the hood when the wiper arm is lifted up. The wiper and hood

may be damaged.

• Do not operate the wiper when the washer fluid reservoir is empty.

• Since there is no way to successfully remove traces of oil or grease

from any glass, be certain not to apply any polish containing oil to the
windshield of your vehicle since this will result in streaks which impair
vision. Contamination of either the window or the wiper blades with for-
eign matter can reduce the effectiveness of the windshield wipers.

CAUTION

• Never drive your vehicle when the wipers are not properly working.

• Do not touch the running wipers. It may cause a personal injury.

WARNING

«
...
246
247
248
249
250
...
»

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands