manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 55

INTERIOR SWITCHES

4 - 7

WIPER AND WASHER SWITCH

Front Washer Fluid
Reservoir

Frequently check the washer fluid level and add with speci-
fied washer fluid.

Rear Washer Fluid
Reservoir

Rain Sensor*

When the windshield wiper
switch is at “AUTO” position,
the rain sensor automatically
turns on and off the wiper. And,
it controls the wiping speed by
detecting the amount of rain
drops.

Rear Wiper and
Washer Switch

C. Rear wiper operation

D. Rear wiper and washer

operation

E. Rear wiper stops

Front Wiper and Washer
Switch

A. Front wiper and washer

switch

B. Automatic wiper control

switch

• If you use plain water as washer fluid, it will freeze during the win-

ter and damage the washer fluid tank and motor. Use only speci-
fied washer fluid.

• Be careful not to spill the washer fluid around the reservoir.

CAUTION

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands