manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 226

SERVICE AND MAINTENANCE

1 3 - 2

Exterior

Interior

The following checks are recommended before driving to
maintain safe and dependable vehicle operation.

1. Check the tyres for inflation pressure and damage.

2. Check the wheel bolts for looseness.

3. Check the operation of the lights.

4. Check for any oil, water, fuel and fluid leaks.

5. Check the outside rearview mirrors and license plate for

dirt or damage.

1. Check for steering wheel free play and looseness.
2. Check the parking brake lever travel.
3. Check the operation of the horn, windshield wipers and

turn signals.

4. Check the operation of instruments and indicator warn-

ing lights.

5. Check level of fuel in the fuel tank against fuel gauge.
6. Check the position of the rearview mirrors.
7. Check the operation of the door locking mechanism.
8. Check the brake and clutch pedal free play, height and

function.

9. Check the seat belts.

DAILY CHECK LIST

If in doubt about driving and operating conditions, have your vehicle
checked at Ssangyong Dealer or Ssangyong Authorized Service
Operation.

CAUTION

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands