manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 195

CONVENIENCE DEVICES

11-15

1. Open the cover and remove the stor-

age bin.

2. To release the bottom locks, lift up

the support from floor and push
both sides of tray in.

3. Open the cover in rear bottom of the

tray. To release left lock, turn the tray
to arrow direction while pushing up
the inner lock button. Pull out the
tray assembly.

4. Put down the lifted

support and push both
sides of tray out.

5. Insert the removed stor-

age bin into the tray and
close the cover.

The length of tray handle
can be adjusted.

REMOVAL AND INSTALLATION OF TRAY

• When pushing both sides of tray out, do not touch the folded area.

It may cause a personal injury.

WARNING

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands