manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 249

SERVICE AND MAINTENANCE

13-25

Tyre Pressure

TYRE INFLATION PRESSURE

Tyre

215/65R16

225/65R16

LT225/65R16

Wheel

6.5J x 16

Specification

Pressure

35 PSI

(2.41 bar)

48 PSI

(3.30 bar)

• Maintaining the specified tyre pressure is essential for driver comfort,

driving safety and long tyre life. Incorrect inflation pressures will in-
crease tyre wear and will impair safety, vehicle handling, comfort
and fuel economy. The tyre inflation pressure should be followed by
the specified pressure.

• Check and adjust the tyre inflation pressure, including the spare

wheel, prior to any long journey (when the tyre is cold).

CAUTION

Increase the tyre inflation pressure by 4~5 psi from the specified value
prior to any long journey.

NOTE

7-Seaters

7, 9-Seaters

11-Seaters

Proper

inflation

Under

inflation

Over

inflation

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands