YOKOGAWA UTAdvanced Series, User Manual

Page: 231 / 866

6-130
IM 05P07A01-01EN
6.4 UT55A/UT52A/UP55A D Registers
6.4.11 Program Pattern for UP55A (D8001 to D9000)
Pattern Data Setting (D8001 to D8100)
Register
No.
Ref.
No.
H No.
Register
symbol
R/W Description Range and meaning of value
D8001 48001 1F40 PTNO._C R/W Program pattern number selection 0: Not select program pattern
1 to 30
D8002 48002 1F41 SEGNO._C R/W Segment number designation
0
(1 to 99)
*:When reading from or writing to D8003 to
D8043 registers, write "0" to the register.
D8003 48003 1F42 SSP_L1 R/W Loop-1 Starting target setpoint
0.0 to 100.0% of PV input range (EU)
(Setting range: P.RL to P.RH)
D8004 48004 1F43 SSP_L2 R/W Loop-2 Starting target setpoint
D8005 48005 1F44 STC R/W Start code
0: SSP (Program operation begins with the
starting target setpoint.
1: RAMP (Ramp-prioritized PV start)
2: TIME (Time-prioritized PV start)
4: LSP (Local-mode start)
5: RSP (Remote-mode start)
* STC=TIME cannot be selected when the
parameter SEG.T is TM.RT.
D8006 48006 1F45 WT.SW1 R/W Wait function ON/OFF 1
WT.SW1 to WT.SW5
0: OFF (Disable)
1: ON (Enable)
WZ.UP1 to WZ.UP5
0.0 to 10.0% of PV input range (EU)
WT.TM1 to WT.TM5
0: OFF (No function)
1 to 59999 (minute or second)
* Available only for the wait time at the segment
switching.
* Use the parameter TMU to set the time unit.
(Common in the instrument.)
D8007 48007 1F46 WZ.UP1 R/W Upper-side wait zone 1
D8008 48008 1F47 WZ.LO1 R/W Lower-side wait zone 1
D8009 48009 1F48 WT.TM1 R/W Wait time 1
D8010 48010 1F49 WT.SW2 R/W Wait function ON/OFF 2
D8011 48011 1F4A WZ.UP2 R/W
Upper-side wait zone 2
D8012 48012 1F4B WZ.LO2 R/W Lower-side wait zone 2
D8013 48013 1F4C WT.TM2 R/W Wait time 2
D8014 48014 1F4D WT.SW3 R/W Wait function ON/OFF 3
D8015 48015 1F4E WZ.UP3 R/W Upper-side wait zone 3
D8016 48016 1F4F WZ.LO3 R/W Lower-side wait zone 3
D8017 48017 1F50 WT.TM3 R/W Wait time 3
D8018 48018 1F51 WT.SW4 R/W Wait function ON/OFF 4
D8019 48019 1F52 WZ.UP4 R/W Upper-side wait zone 4
D8020 48020 1F53 WZ.LO4 R/W Lower-side wait zone 4
D8021 48021 1F54 WT.TM4 R/W Wait time 4
D8022 48022 1F55 WT.SW5 R/W Wait function ON/OFF 5
D8023 48023 1F56
WZ.UP5
R/W
Upper-side wait zone 5
D8024 48024 1F57 WZ.LO5 R/W Lower-side wait zone 5
D8025 48025 1F58 WT.TM5 R/W Wait time 5
D8026 48026 1F59 R.CYCL R/W Number of repeat cycles
0 to 999, 1000: CONT (The controller indefinitely
repeats the segment specified by the RST and
REN parameters.)
D8027 48027 1F5A R.STRT R/W Repeat cycle start segment
number
1 to 99
1 ≤ R.STRT ≤ R.END ≤ 99
D8028 48028 1F5B R.END R/W Repeat cycle end segment number
D8029 48029 1F5C
D8030 48030 1F5D
D8031 48031 1F5E P.NAME
R/W Program pattern name
20-digit value of alphanumeric characters can be
set.
Arrangement:
D8031, D8032, D8033, D6004, D8035, D8036,
D8037, D8038, D8039, D8040, D8041
Write “0x00” to the register after the character
string.
D8032 48032 1F5F P.NAME R/W Program pattern name
D8033 48033 1F60 P.NAME R/W Program pattern name
D8034 48034 1F61 P.NAME R/W Program pattern name
D8035 48035 1F62 P.NAME R/W Program pattern name
D8036 48036 1F63 P.NAME R/W Program pattern name
D8037 48037 1F64 P.NAME R/W Program pattern name
D8038 48038 1F65 P.NAME R/W Program pattern name
D8039 48039 1F66 P.NAME R/W Program pattern name
D8040 48040 1F67 P.NAME R/W Program pattern name
D8041 48041 1F68 P.NAME R/W Program pattern name
D8042 48042 1F69 PTN.ERR R Read/write error information
0: Normal end
Except 0: error (See "Error information"
described later in this chapter.)
D8043 to D8100