Texas Instruments Concerto F28M36 Series Technical Reference Manual Download | Manualshive

Page: 1503 / 1692

background image

Register Descriptions

1503

SPRUHE8E – October 2012 – Revised November 2019

Submit Documentation Feedback

Copyright © 2012–2019, Texas Instruments Incorporated

M3 Universal Asynchronous Receivers/Transmitters (UARTs)

21.7.4 UART IrDA Low-Power Register (UARTILPR), offset 0x020

The UARTILPR register stores the 8-bit low-power counter divisor value used to derive the low-power SIR
pulse width clock by dividing down the system clock (SysClk). All the bits are cleared when reset.

The internal IrLPBaud16 clock is generated by dividing down SysClk according to the low-power divisor
value written to UARTILPR. The duration of SIR pulses generated when low-power mode is enabled is
three times the period of the IrLPBaud16 clock. The low-power divisor value is calculated as follows:

ILPDVSR = SysClk / F

IrLPBaud16

where F

IrLPBaud16

is nominally 1.8432 MHz.

The divisor must be programmed such that 1.42 MHz < F

IrLPBaud16

< 2.12 MHz, resulting in a low-power

pulse duration of 1.41-2.11 µs (three times the period of IrLPBaud16). The minimum frequency of
IrLPBaud16 ensures that pulses less than one period of IrLPBaud16 are rejected, but pulses greater than
1.4 µs are accepted as valid pulses.

NOTE:

Zero is an illegal value. Programming a zero value results in no IrLPBaud16 pulses being

generated.

Figure 21-11. UART IrDA Low-Power Register (UARTILPR)

31

8

7

0

Reseved

ILPDVSR

R-0

R/W-0

LEGEND: R/W = Read/Write; R = Read only; -

n

= value after reset

Table 21-6. UART IrDA Low-Power Register (UARTILPR) Field Descriptions

Bit

Field

Value

Description

31-8

Reserved

Reserved

7-0

ILPDVSR

IrDA Low-Power Divisor
This field contains the 8-bit low-power divisor value.

21.7.5 UART Integer Baud-Rate Divisor Register (UARTIBRD), offset 0x024

The UARTIBRD register is the integer part of the baud-rate divisor value. All the bits are cleared on reset.
The minimum possible divide ratio is 1 (when UARTIBRD=0), in which case the UARTFBRD register is
ignored. When changing the UARTIBRD register, the new value does not take effect until
transmission/reception of the current character is complete. Any changes to the baud-rate divisor must be
followed by a write to the UARTLCRH register. See

for configuration details.

Figure 21-12. UART Integer Baud-Rate Divisor Register (UARTIBRD)

31

16 15

0

Reserved

DIVINT

R-0

R/W-0

LEGEND: R/W = Read/Write; R = Read only; -

n

= value after reset

Table 21-7. UART Integer Baud-Rate Divisor (UARTIBRD) Register Field Descriptions

Bit

Field

Value

Description

31-16

Reserved

Reserved

15-0

DIVINT

Integer Baud-Rate Divisor

«
...
1501
1502
1503
1504
1505
...
»

Summary of Contents for Concerto F28M36 Series





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Concerto F28M36 Series

Brand: S&C Pages: 40

Brand: iCeeO2 Pages: 7

Brand: Danfoss Pages: 32

VLT AutomationDrive FC 360

Brand: Danfoss Pages: 60

Brand: Danfoss Pages: 4

ECL Comfort 110

Brand: Danfoss Pages: 2

Brand: DayTronic Pages: 22

Brand: Harman Kardon Pages: 25

Brand: Uniss Pages: 21

Brand: Parkside Pages: 65

Brand: GEM Pages: 17

Brand: PI Pages: 111

Brand: Danfoss Pages: 6

Brand: National Instruments Pages: 20

BACnet 4M230.8I AP

Brand: WAREMA Pages: 4

Brand: Inkbird Pages: 10

Brand: Wachendorff Pages: 35

Brand: TDSi Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands