Renesas H8S Family Hardware Manual Download

Page: 949 / 1230

Section 23

A/D Converter

Rev. 1.00 Mar. 12, 2008 Page 901 of 1178

REJ09B0403-0100

23.3.3

A/D Control Register (ADCR)

The ADCR sets the operation mode of A/D converter and the conversion time.

Bit Bit

Name

Initial
Value

R/W Description

TRGS1

TRGS0

EXTRGS

R/W

Timer Trigger Select 1 and 0, Extended Trigger Select

Enable starting of A/D conversion by a trigger signal.

00 0: Disables starting by trigger signals.

10 0: Enables starting by a trigger from TMR_0.

10 1: Enables starting by the

ADTRG

pin input.

Other than above: Setling prohibited

SCANE

SCANS

R/W

Scan Mode

Select the operation mode of A/D conversion

0x: Single mode

10: Scan mode

(consecutive A/D conversion of channels 1 to 4)

11: Scan mode

(consecutive A/D conversion of channels 1 to 8)

CKS1

CKS0

R/W

Clock Select 1 and 0

Set the A/D conversion time. Setting should be made
while the conversion is stopped (ADST = 0).

00: Setting prohibited

01: Conversion time = 80 states (max) (20 MHz or less)

10: Conversion time = 160 states (max)

11: Conversion time = 320 states (max)

ADSTCLR

R/W

A/D Start Clear

Sets automatic clearing of the ADST bit in scan mode.

0: Disables automatic clearing of ADST in scan mode.

1: ADST is automatically cleared when A/D conversion for

all the selected channels has been completed in scan
mode.

[Legend]

x: Don't care

Summary of Contents for H8S Family















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for H8S Family

Reviews:

Related manuals for H8S Family

Brands by name

Popular brands

Renesas H8S Family, Hardware Manual

Search results

Summary of Contents for H8S Family

Reviews:

Related manuals for H8S Family

Brands by name

Popular brands