Renesas H8S Family Hardware Manual Download | Manualshive

Page: 854 / 1230

background image

Section 21 Ethernet Controller Direct Memory Access Controller (E-DMAC)

Rev. 1.00 Mar. 12, 2008 Page 806 of 1178

REJ09B0403-0100

21.2.8

Transmit/Receive Status Copy Enable Register (TRSCER)

TRSCER specifies whether or not transmit and receive status information reported by bits in the
EtherC/E-DMAC status register is to be indicated in bits TFS26 to TFS0 and RFS26 to RFS0 in
the corresponding descriptor. Bits in this register correspond to bits 11 to 0 in the EtherC/E-
DMAC status register (EESR). When a bit is cleared to 0, the transmit status (bits 11 to 8 in
EESR) is indicated in bits TFS3 to TFS0 in the transmit descriptor, and the receive status (bits 7
to 0 in EESR) is indicated in bits RFS7 to RFS0 of the receive descriptor. When a bit is set to 1,
the occurrence of the corresponding interrupt is not indicated in the descriptor. After this LSI is
reset, all bits are cleared to 0.

Bit Bit

Name

Initial
value

R/W Description

31 to 12



All

0

R

Reserved

These bits are always read as 0. The initial value
should not be changed.

11

CNDCE

0

R/W

CND Bit Copy Directive

0: Indicates the CND bit state in bit TFS3 in the

transmit descriptor

1: Occurrence of the corresponding interrupt is not

indicated in bit TFS3 of the transmit descriptor

10

DLCCE

0

R/W

DLC Bit Copy Directive

0: Indicates the DLC bit state in bit TFS2 of the

transmit descriptor

1: Occurrence of the corresponding interrupt is not

indicated in bit TFS2 of the transmit descriptor

9

CDCE

0

R/W

CD Bit Copy Directive

0: Indicates the CD bit state in bit TFS1 of the transmit

descriptor

1: Occurrence of the corresponding interrupt is not

indicated in bit TFS1 of the transmit descriptor

8

TROCE

0

R/W

TRO Bit Copy Directive

0: Indicates the TRO bit state in bit TFS0 of the receive

descriptor

1: Occurrence of the corresponding interrupt is not

indicated in bit TFS0 of the receive descriptor

«
...
852
853
854
855
856
...
»

Summary of Contents for H8S Family















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S Family

Brand: SIIG Pages: 12

Brand: Lanner Pages: 109

Brand: Acces I/O products Pages: 5

SINUS H PROFInet

Brand: Enertronica Santerno Pages: 34

Brand: AXIOMTEK Pages: 2

640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU

Brand: Intel Pages: 105

Wisenet XRN-6410RB2-24TB

Brand: Hanwha Techwin Pages: 124

AirStation G54 WLA2-G54

Brand: Buffalo Pages: 8

Brand: AMD Pages: 27

Brand: EXAGATE Pages: 7

Brand: Multi-Link Pages: 31

Brand: MicroNova Pages: 113

ENHANCED PSD 239 H2R

Brand: ADTRAN Pages: 2

Brand: B&B Electronics Pages: 74

Brand: Planet Pages: 38

Brand: ADTRAN Pages: 2

Brand: ADTRAN Pages: 2

Brand: ADTRAN Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands