Renesas H8S Family Hardware Manual Download | Manualshive

Page: 941 / 1230

background image

Section 22 USB Function Module (USB)

Rev. 1.00 Mar. 12, 2008 Page 893 of 1178

REJ09B0403-0100

22.10.4 Assigning Interrupt Sources to EP0

The EP0-related interrupt sources indicated by the interrupt source bits (bits 0 to 3) in IFR0 must
be assigned to the same interrupt signal with ISR0. The other interrupt sources have no limitations.

22.10.5 Clearing the FIFO When DTC Transfer is Enabled

The endpoint 1 data register (EPDR1) cannot be cleared when DTC transfer for endpoint 1 is
enabled (EP1DMAE in DMA = 1). Cancel DTC transfer before clearing the register.

22.10.6 Notes on TR Interrupt

Note the following when using the transfer request interrupt (TR interrupt) for IN transfer to EP0i,
EP2, or EP3.

The TR interrupt flag is set if the FIFO for the target EP has no data when the IN token is sent
from the USB host. However, at the timing shown in figure 22.24, multiple TR interrupts occur
successively. Take appropriate measures against malfunction in such a case.

Note: This module determines whether to return NAK if the FIFO of the target EP has no data

when receiving the IN token, but the TR interrupt flag is set after a NAK handshake is
sent. If the next IN token is sent before PKTE of TRG is written to, the TR interrupt flag is
set again.

CPU

Host

IN token

IN token

IN token

Sets TR flag
(Sets the flag again)

Sets TR flag

Determines whether
to return NAK

Transmits data

TR interrupt routine

Clear
TR flag

Writes
transmit data

TRG.
PKTE

TR interrupt routine

USB

NAK

Determines whether
to return NAK

NAK

ACK

Figure 22.23 TR Interrupt Flag Set Timing

«
...
939
940
941
942
943
...
»

Summary of Contents for H8S Family















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S Family

Brand: NEC Pages: 47

Brand: Patton electronics Pages: 51

Brand: Palo Alto Network Pages: 56

Brand: Clavister Pages: 89

Brand: Lorex Pages: 186

Brand: Moxa Technologies Pages: 19

Brand: Maxim Pages: 14

EXPANSION CARD X-DANTE

Brand: Behringer Pages: 65

RabbitCore RCM4400W

Brand: Rabbit Pages: 126

Thin Client US310e

Brand: NEC Pages: 6

PCIe/PXIe-6301 Series

Brand: JYTEK Pages: 46

Brand: Digi Pages: 116

Brand: Renesas Pages: 4

Brand: ETAS Pages: 36

Brand: UMAX Technologies Pages: 27

Quark SoC X1000

Brand: Galileo Pages: 20

HHM Series HHM1521

Brand: TDK Pages: 2

Brand: ICP DAS USA Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands