Renesas H8S Family Hardware Manual Download | Manualshive

Page: 608 / 1230

background image

Section 17 Synchronous Serial Communication Unit (SSU)

Rev. 1.00 Mar. 12, 2008 Page 560 of 1178

REJ09B0403-0100

Bit Bit

Name

Initial
Value

R/W Description

2

TDRE

1

R/W

Transmit Data Empty

Indicates whether or not SSTDR contains transmit data.

[Setting conditions]

•

When the TE bit in SSER is 0

•

When data is transferred from SSTDR to SSTRSR
and SSTDR is ready to be written to.

[Clearing conditions]

•

When writing 0 after reading TDRE

=

1

•

When writing data to SSTDR with TE

=

1

1

RDRF

0

R/W

Receive Data Register Full

Indicates whether or not SSRDR contains receive data.

[Setting condition]

•

When receive data is transferred from SSTRSR to
SSRDR after successful serial data reception

[Clearing conditions]

•

When writing 0 after reading RDRF

=

1

•

When reading receive data from SSRDR

0 CE 0 R/W

Conflict/Incomplete

Error

Indicates that a conflict error has occurred
when 0 is externally input to the

SCS

pin with SSUMS

=

0 (SSU mode) and MSS

=

1 (master mode).

If the

SCS

pin level changes to 1 with SSUMS

=

0 (SSU

mode) and MSS

=

0 (slave mode), an incomplete error

occurs because it is determined that a master device
has terminated the transfer. Data reception does not
continue while the CE bit is set to 1. Serial transmission
also does not continue. Reset the SSU internal
sequencer by setting the SRES bit in SSCRL to 1
before resuming transfer after incomplete error.

[Setting condition]

•

When a low level is input to the

SCS

pin in master

mode (the MSS bit in SSCRH is set to 1)

•

When the

SCS

pin is changed to 1 during transfer in

slave mode (the MSS bit in SSCRH is cleared to 0)

[Clearing condition]

•

When writing 0 after reading CE

=

1

«
...
606
607
608
609
610
...
»

Summary of Contents for H8S Family















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S Family

Brand: 3Com Pages: 20

Express EtherNetwork DFE-670TXD

Brand: D-Link Pages: 4

Brand: DAD Pages: 36

Brand: D-Link Pages: 2

Brand: Samsung Pages: 65

Brand: M86 Security Pages: 46

Brand: Dahua Pages: 24

Brand: Intel Pages: 108

Brand: Lanner Pages: 63

Brand: Nvidia Pages: 115

Brand: Accom Pages: 15

HBJC924R3288DG2NS Series

Brand: JETWAY Pages: 6

TD-3316B4-16P-A1

Brand: TVT Digital Pages: 2

Brand: Omron Pages: 13

Brand: ETAS Pages: 82

Brand: Comelit Pages: 19

crown PIP Series

Brand: Harman Pages: 16

Brand: ETAS Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands