Renesas H8S Family Hardware Manual Download | Manualshive

Page: 160 / 1230

background image

Section 6 Bus Controller (BSC)

Rev. 1.00 Mar. 12, 2008 Page 112 of 1178

REJ09B0403-0100

6.3.3

Wait State Control Register (WSCR)

WSCR is used to specify the data bus width, the number of access states, the wait mode, and the
number of wait states for access to external address spaces (basic extended area and 256-Kbyte
extended area). The bus width and the number of access states for internal memory and internal
I/O registers are fixed regardless of the WSCR settings.

Bit Bit

Name

Initial
Value

R/W Description

7

ABW256

1

R/W

256-Kbyte Extended Area Bus Width Control

Selects the bus width for access to the 256-Kbyte
extended area when the CS256E bit in SYSCR is set to 1.

0: 16-bit bus

1: 8-bit bus

6

AST256

1

R/W

256-Kbyte Extended Area Access State Control

Selects the number of states for access to the 256-Kbyte
extended area when the CS256E bit in SYSCR is set to 1.
This bit also enables or disables wait-state insertion.

[ADMXE = 0] Normal extension

0: 2-state access space. Wait state insertion disabled

1: 3-state access space. Wait state insertion enabled

[ADMXE = 1] Address-data multiplex extension

0: 2-state data access space. Wait state insertion disabled

1: 3-state data access space. Wait state insertion enabled

5

ABW

1

R/W

Basic Extended Area Bus Width Control

Selects the bus width for access to the basic extended
area.

0: 16-bit bus

1: 8-bit bus

When the CS256E bit in SYSCR is set to 1, this bit setting
is ignored in access to the 256-Kbyte extended area.

«
...
158
159
160
161
162
...
»

Summary of Contents for H8S Family















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S Family

Brand: IEI Technology Pages: 19

Brand: IEI Technology Pages: 87

Brand: IEI Technology Pages: 3

Brand: National Instruments Pages: 11

Brand: Maxim Pages: 26

Brand: Delta Electronics Pages: 1

USB-BRIDGEV2-EVAL

Brand: IDT Pages: 11

Brand: RAIDAGE Pages: 60

Brand: ZALMAN Pages: 11

dspstak 21262sx

Brand: Danville Signal Processing Pages: 35

Brand: Medel Pages: 28

Brand: Wyse Pages: 8

Brand: Advantech Pages: 66

Brand: M-system Pages: 4

Powereta iQP Series

Brand: TDK Pages: 2

NC-MCO - TECHNICAL

Brand: Crest Audio Pages: 2

PSJ-VZ58 gen3 OEM

Brand: Grizzly Pages: 12

SPEEDTOUCH 110G

Brand: THOMSON Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands