Renesas H8S Family Hardware Manual Download

Page: 675 / 1230

Section 18

C Bus Interface (IIC)

Rev. 1.00 Mar. 12, 2008 Page 627 of 1178

REJ09B0403-0100

Receive Operation Using the Wait Function:

Figures 18.13 and 18.14 show the sample flowcharts for the operations in master receive mode
(WAIT = 1).

Set TRS = 0 in ICCR

Set ACKB = 0 in ICSR

Set WAIT = 1 in ICMR

Yes

Clear IRIC in ICCR

Read IRIC in ICCR

Last receive?

IRIC = 1?

IRTR = 1?

Yes

IRTR=1?

Read IRIC in ICCR

IRIC=1?

Yes

Read ICDR

[4] Determine end of reception

[13] Determine end of reception

[1] Select receive mode.

[2] Start receiving. The first read

is a dummy read.

[3] Wait for a receive wait
(Set IRIC at the fall of the 8th clock) or,
Wait for 1 byte to be received
(Set IRIC at the rise of the 9th clock)

[12] Wait for a receive wait
(Set IRIC at the fall of the 8th clock) or,
Wait for 1 byte to be received
(Set IRIC at the rise of the 9th clock)

[5] Read the receive data.

[6] Clear IRIC.

(to end the wait insertion)

[15] Clear wait mode.
Clear IRIC.

( IRIC should be cleared to 0

after setting WAIT = 0.)

[17] Generate stop condition

Master receive mode

[14] Clear IRIC.

(to end the wait insertion)

[16] Read the last receive data.

[7] Set acknowledge data for the last reception.

[8] Wait for TRS setting

[9] Set TRS for stop condition issuance

[10] Read the receive data.

[11] Clear IRIC.

Read ICDR

Clear IRIC in ICCR

Set HNDS = 0 in ICXR

Wait for one clock pulse

Set ACKB = 1 in ICSR

Set TRS = 1 in ICCR

End

Set WAIT = 0 in ICMR

Set BBSY= 0 and SCP= 0

in ICCR

Clear IRIC in ICCR

Read ICDR

Clear IRIC in ICCR

Read ICDR

Figure 18.13 Sample Flowchart for Operations in Master Receive Mode

(receiving multiple bytes) (WAIT = 1)

Summary of Contents for H8S Family















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for H8S Family

Reviews:

Related manuals for H8S Family

Brands by name

Popular brands

Renesas H8S Family, Hardware Manual

Search results

Summary of Contents for H8S Family

Reviews:

Related manuals for H8S Family

Brands by name

Popular brands