Renesas H8S Family Hardware Manual Download | Manualshive

Page: 842 / 1230

background image

Section 21 Ethernet Controller Direct Memory Access Controller (E-DMAC)

Rev. 1.00 Mar. 12, 2008 Page 794 of 1178

REJ09B0403-0100

21.2.1

E-DMAC Mode Register (EDMR)

EDMR is a 32-bit readable/writable register that specifies the operating mode of the E-DMAC.
The settings in this register are normally made in the initialization process following a reset. If the
EtherC and E-DMAC are initialized by means of this register during data transmission, abnormal
data may be sent onto the line. Operating mode settings must not be changed while the transmit
and receive functions are enabled. To change the operating mode, the EtherC and E-DMAC
modules are got into at their initial state by means of the software reset bit (SWR) in this register,
then make new settings. It takes 64 states to initialize the EtherC and E-DMAC. Therefore,
registers of the EtherC and E-DMAC should be accessed after 64 states have elapsed.

Bit Bit

Name

Initial
value

R/W Description

31 to 7



All

0

R

Reserved

These bits are always read as 0. The initial value
should not be changed.

6

DE

0

R/W

E-DMAC Data Endian Convert

Selects whether or not the endian format is converted
on data transfer by the E-DMAC. However, the
endian format of the descriptors and E-DMAC register
values are not converted regardless of this bit setting.

0: Endian format not converted (big endian)

1: Endian format converted (little endian)

5

4

DL1

DL0

0

0

R/W

R/W

Transmit/Receive Descriptor Length

These bits specify the transmit/receive descriptor
length.

00: 16 bytes

01: 32 bytes

10: 64 bytes

11: Setting prohibited

3 to 1



All

0

R

Reserved

These bits are always read as 0. The initial value
should not be changed.

«
...
840
841
842
843
844
...
»

Summary of Contents for H8S Family















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S Family

DHI-NVR5224-24P-4KS2

Brand: Dahua Pages: 24

Brand: Octavo Pages: 28

Brand: Obihai Pages: 2

SRCSASBB8I - RAID Controller

Brand: Intel Pages: 36

Storagelibrary T24

Brand: Tandberg Data Pages: 28

Brand: AMD Pages: 45

Vortex86SX VSX-6100

Brand: ICOP Technology Pages: 50

DEEP LEARNING PLUS

Brand: Concept Pro Pages: 28

Brand: Magewell Pages: 10

Brand: Z3 Technology Pages: 18

Brand: Keithley Pages: 108

Hotwire 5620 RTU

Brand: Paradyne Pages: 20

Brand: Primera Pages: 82

Brand: Adaptec Pages: 2

Brand: TECO Pages: 24

Brand: Avaya Pages: 2

Brand: Cabletron Systems Pages: 54

Brand: Citizen Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands