Renesas H8S Family Hardware Manual Download | Manualshive

Page: 810 / 1230

background image

Section 20 Ethernet Controller (EtherC)

Rev. 1.00 Mar. 12, 2008 Page 762 of 1178

REJ09B0403-0100

Bit Bit

Name

Initial
Value

R/W Description

16

TXF

0

R/W

Transmit Flow Control Operating mode

0: Transmit flow control function is disabled

(automatic PAUSE frames are not transmitted)

1: Transmit flow control function is enabled

(automatic PAUSE frame is transmitted as
necessary)

15 to 13



All

0

R Reserved

These bits are always read as 0. The initial value
should not be changed.

12

PRCEF

0

R/W

Permit Receive CRC Error Frame

0: A frame with a CRC error is received as a frame

with an error.

1: A frame with a CRC error is received as a frame

without an error. The CEFCR register is therefore
not incremented.

If this bit is clear and a frame with an error is received,
a CRC error is reflected in ECSR of the E-DMAC and
the status of the receive descriptor. If this bit is set to
1, a frame with an error is received as a normal frame.

11, 10



All

0

R Reserved

These bits are always read as 0. The initial value
should not be changed.

9

MPDE

0

R/W

Magic Packet Detection Enable

Enables or disables Magic Packet detection by
hardware to allow activation from the Ethernet.

0: Magic Packet detection is not enabled

1: Magic Packet detection is enabled

8, 7



All

0

R Reserved

These bits are always read as 0. The initial value
should not be changed.

6 RE

0 R/W

Reception

Enable

0: Receive function is disabled

1: Receive function is enabled

If this bit is changed from enabling to disabling while a
frame is being received, the receive function remains
enabled until reception of the frame is completed.

«
...
808
809
810
811
812
...
»

Summary of Contents for H8S Family















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S Family

i-bus KNX IPR/S 3.5.1

Brand: ABB Pages: 44

Brand: NEC Pages: 72

ELECTRA ELITE IPK II

Brand: NEC Pages: 617

VERSA DOCK - SERVICE

Brand: NEC Pages: 8

Brand: Lattice Semiconductor Pages: 15

Brand: Lanner Pages: 109

Brand: Gate Pages: 8

Brand: East Coast Datacom Pages: 19

Brand: Variscite Pages: 18

Brand: Magma Pages: 2

Brand: Cypress Semiconductor Pages: 15

LITTLE BOARD P5X

Brand: Ampro Corporation Pages: 121

Brand: Planet Pages: 20

TeleMyo 2400T V2

Brand: Noraxon Pages: 52

Brand: audemat Pages: 93

Internal All-in-One Digital Media Drive ULT31793

Brand: Ultra Products Pages: 1

Brand: Dinstar Pages: 103

Brand: Datalogic Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands