Renesas H8S Family Hardware Manual Download | Manualshive

Page: 765 / 1230

background image

Section 19

LPC Interface (LPC)

Rev. 1.00 Mar. 12, 2008 Page 717 of 1178

REJ09B0403-0100

19.3.24 SMIC Interrupt Register 1 (SMICIR1)

SMICIR1 is one of the registers used to implement SMIC mode. This register includes the bits that
enables/disables an interrupt to the slave. The IBFI3 interrupt is enabled by setting the IBFIE3 bit
in HICR2 to 1.

R/W

Bit

Bit Name Initial Value Slave Host Description

7 to 5



All

0

R/W



Reserved

The initial value should not be changed.

4 HDTWIE

0

R/W



Transfer Data Transmission End Interrupt Enable

Enables or disables HDTWI interrupt that is IBFI3
interrupt source to the slave.

0: Disables transfer data transmission end interrupt

1: Enables transfer data transmission end interrupt

3 HDTRIE

0

R/W



Transfer Data Receive End Interrupt Enable

Enables or disables HDTRI interrupt that is IBFI3
interrupt source to the slave.

0: Disables transfer data receive end interrupt

1: Enables transfer data receive end interrupt

2 STARIE

0

R/W



Status Code Receive End Interrupt Enable

Enables or disables STARI interrupt that is IBFI3
interrupt source to the slave.

0: Disables status code receive end interrupt

1: Enables status code receive end interrupt

1 CTLWIE

0

R/W



Control Code Transmission End Interrupt Enable

Enables or disables CTLWI interrupt that is IBFI3
interrupt source to the slave.

0: Disables control code transmission end interrupt

1: Enables control code transmission end interrupt

0 BUSYIE

0

R/W



Transfer Start Interrupt Enable

Enables or disables BUSYI interrupt that is IBFI3
interrupt source to the slave.

0: Disables transfer start interrupt

1: Enables transfer start interrupt

«
...
763
764
765
766
767
...
»

Summary of Contents for H8S Family















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S Family

Brand: 3Com Pages: 8

Brand: Queclink Pages: 9

Armor 101 Series

Brand: Lochinvar Pages: 28

Armor 101 Series

Brand: Lochinvar Pages: 44

Brand: Orban Pages: 255

OMB-DAQBOARD-3000 Series

Brand: Omega Pages: 108

Brand: Altera Pages: 93

NetVanta 6355 PoE

Brand: ADTRAN Pages: 46

Brand: Comtrend Corporation Pages: 4

Brand: Laser Pages: 4

CORE 2 DUO E4000 - 3-2008

Brand: Intel Pages: 122

Brand: Dave Embedded Systems Pages: 79

Brand: ST Pages: 64

Brand: TECO Pages: 24

Brand: TERSUS Pages: 7

Embedded Intelligent Module SX-560

Brand: Silex technology Pages: 110

JNLH61S-6C Series

Brand: JETWAY Pages: 36

593/25, 593/45, 593/TB, RS-422, RS-485

Brand: Patton electronics Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands