Renesas H8S Family Hardware Manual Download | Manualshive

Page: 818 / 1230

background image

Section 20 Ethernet Controller (EtherC)

Rev. 1.00 Mar. 12, 2008 Page 770 of 1178

REJ09B0403-0100

20.3.8

PHY Status Register (PSR)

PSR is a read-only register that can read interface signals from the PHY.

Bit Bit

Name

Initial
Value

R/W Description

31 to 1



All

0

R

Reserved

These bits are always read as 0. The initial value
should not be changed.

0

LMON

0

R

LNKSTA Pin Status

The Link status can be read by connecting the Link
signal output from the PHY to the LNKSTA pin. For
the polarity, refer to the PHY specifications to be
connected.

20.3.9

Transmit Retry Over Counter Register (TROCR)

TROCR is a 32-bit counter that indicates the number of frames that were unable to be transmitted
in 16 transmission attempts including the retransmission. When 16 transmission attempts have
failed, TROCR is incremented by 1. When the value in this register reaches H'FFFFFFFF, the
count is halted. The counter value is cleared to 0 by a write to this register with any value.

Bit Bit

Name

Initial
Value

R/W Description

31 to 0 TROC31 to

TROC0

All 0

R/W

Transmit Retry Over Count

These bits indicate the number of frames that were
unable to be transmitted in 16 transmission attempts
including retransmission.

«
...
816
817
818
819
820
...
»

Summary of Contents for H8S Family















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S Family

Brand: Ubiquiti Pages: 24

Brand: ETAS Pages: 69

Brand: Paradyne Pages: 1

Brand: Cypress Semiconductor Pages: 16

PBE-5AC-300-ISO

Brand: Ubiquiti Pages: 28

Brand: MICROENER Pages: 24

NVR41-4KS2 Series

Brand: Dahua Pages: 452

Brand: ZALMAN Pages: 16

Brand: IBM Pages: 130

COM Express conga-TC87

Brand: Congatec Pages: 114

Brand: S&P Pages: 3

Brand: ProSoft Pages: 53

Digital Loudspeaker

Brand: Dolby Laboratories Pages: 4

Brand: MCT Pages: 12

SATA II-150 PCI

Brand: SIIG Pages: 16

2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 1 01-2011

Brand: Intel Pages: 172

Dablet DVP 5000

Brand: DarbeeVision Pages: 10

Brand: TRENDnet Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands