Renesas H8S Family Hardware Manual Download | Manualshive

Page: 649 / 1230

background image

Section 18

I

2

C Bus Interface (IIC)

Rev. 1.00 Mar. 12, 2008 Page 601 of 1178

REJ09B0403-0100

Bit Bit

Name

Initial
Value R/W

Description

1 IRIC 0 R/(W)

*

I

2

C Bus Interface Interrupt Request Flag

Indicates that the I

2

C bus interface has issued an interrupt

request to the CPU.
IRIC is set at different times depending on the FS bit in
SAR and the WAIT bit in ICMR. See section 18.4.7, IRIC
Setting Timing and SCL Control. The conditions under
which IRIC is set also differ depending on the setting of the
ACKE bit in ICCR.

[Setting conditions]
I

2

C bus format master mode:

•

When a start condition is detected in the bus line state

after a start condition is issued (when the ICDRE flag is

set to 1 because of first frame transmission)

•

When a wait is inserted between the data and

acknowledge bit when the WAIT bit is 1 (fall of the 8th

transmit/receive clock)

•

At the end of data transfer (rise of the 9th

transmit/receive clock)

•

When a slave address is received after bus mastership

is lost

•

If 1 is received as the acknowledge bit (when the ACKB

bit in ICSR is set to 1) when the ACKE bit is 1

•

When the AL flag is set to 1 after bus mastership is lost

while the ALIE bit is 1

I

2

C bus format slave mode:

•

When the slave address (SVA or SVAX) matches

(when the AAS or AASX flag in ICSR is set to 1) and at

the end of data transfer up to the subsequent

retransmission start condition or stop condition

detection (rise of the 9th clock)

•

When the general call address is detected (when the 0

is received for R/

W

bit, and ADZ flag in ICSR is set to

1) and at the end of data reception up to the

subsequent retransmission start condition or stop

condition detection (rise of the 9th receive clock)

•

When 1 is received as an acknowledge bit while the

ACKE bit is 1 (when the ACKB bit is set to 1)

•

When a stop condition is detected while the STOPIM bit

is 0 (when the STOP or ESTP flag in ICSR is set to 1)

«
...
647
648
649
650
651
...
»

Summary of Contents for H8S Family















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S Family

Brand: Salto Pages: 2

Brand: 3Com Pages: 18

Brand: Supermicro Pages: 24

Brand: LogLogic Pages: 30

DM/IP601-CPCI-100BT

Brand: Dialogic Pages: 2

Brand: VCS Pages: 118

Brand: IEI Technology Pages: 136

Brand: Beckhoff Pages: 84

Brand: Carrier Pages: 18

Brand: Qvis Pages: 233

Brand: Abus Pages: 98

Brand: IBASE Technology Pages: 49

939GT2-Ultra Series

Brand: JETWAY Pages: 55

Brand: InfoStor Pages: 6

Facility Explorer

Brand: Johnson Controls Pages: 33

Brand: SCT Pages: 2

Brand: Pico Macom Pages: 8

Brand: Dell Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands