Renesas H8S Family Hardware Manual Download | Manualshive

Page: 850 / 1230

background image

Section 21 Ethernet Controller Direct Memory Access Controller (E-DMAC)

Rev. 1.00 Mar. 12, 2008 Page 802 of 1178

REJ09B0403-0100

Bit Bit

Name

Initial
value

R/W Description

8

TRO

0

R/W

Transmit Retry Over

Indicates that a retry-over condition has occurred
during frame transmission. Total 16 transmission
retries including 15 retries based on the back-off
algorithm are failed after the EtherC transmission
starts.

0: Transmit retry-over condition not detected

1: Transmit retry-over condition detected

7

RMAF

0

R/W

Receive Multicast Address Frame

0: Multicast address frame has not been received

1: Multicast address frame has been received

6, 5



All

0

R

Reserved

These bits are always read as 0. The initial value
should not be changed.

4

RRF

0

R/W

Receive Residual-Bit Frame

0: Residual-bit frame has not been received

1: Residual-bit frame has been received

3 RTLF

0 R/W

Receive

Too-Long

Frame

Indicates that the frame more than the number of
receive frame length upper limit set by RFLR of the
EtherC has been received.

0: Too-long frame has not been received

1: Too-long frame has been received

2

RTSF

0

R/W

Receive Too-Short Frame

Indicates that a frame of fewer than 64 bytes has
been received.

0: Too-short frame has not been received

1: Too-short frame has been received

1

PRE

0

R/W

PHY Receive Error

0: PHY receive error not detected

1: PHY receive error detected

0

CERF

0

R/W

CRC Error on Received Frame

0: CRC error not detected

1: CRC error detected

«
...
848
849
850
851
852
...
»

Summary of Contents for H8S Family















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S Family

Brand: Paradox Pages: 4

TWR-SB0410-36EVB

Brand: NXP Semiconductors Pages: 26

Brand: SIIG Pages: 12

Brand: EVS Pages: 30

Brand: SIIG Pages: 6

PoleVault System A/V Source Inputs

Brand: Extron electronics Pages: 4

Storage Networking (Unified Fabric Pilot)

Brand: Qlogic Pages: 76

HIRESCHMANN IT MAMMUTHUS MTM8003-FAN

Brand: Belden Pages: 84

Mercury FireWire 400

Brand: OWC Pages: 2

Brand: Paradyne Pages: 6

Brand: Xantech Pages: 16

Brand: Neousys Technology Pages: 24

netHOST NHST-T100

Brand: hilscher Pages: 75

Brand: Aviosys Pages: 77

Brand: Teridian Pages: 2

Brand: ADS Technologies Pages: 1

Brand: CSL Pages: 24

Network Scanning Unit A

Brand: Ricoh Pages: 206

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands