Renesas H8S Family Hardware Manual Download | Manualshive

Page: 796 / 1230

background image

Section 19 LPC Interface (LPC)

Rev. 1.00 Mar. 12, 2008 Page 748 of 1178

REJ09B0403-0100

The serialized interrupt transfer cycle frame configuration is as follows. Two of the states
comprising each frame are the recover state in which the SERIRQ signal is returned to the 1-level
at the end of the frame, and the turnaround state in which the SERIRQ signal is not driven. The
recover state must be driven by the host or slave that was driving the preceding state.

Table 19.10 Serialized Interrupt Transfer Cycle Frame Configuration

Serial Interrupt Transfer Cycle

Frame
Count

Contents

Drive
Source

Number
of States

Notes

0 Start Slave

Host

6

In quiet mode only, slave drive possible in the
first state, then next 3 states 0-driven by host

1 IRQ0 Slave

3

Drive

impossible

2

IRQ1

Slave

3

Drive possible in LPC channel 1 and SCIF

3

SMI

Slave

3

Drive possible in LPC channels 2, 3, and SCIF

4

IRQ3

Slave

3

Drive possible in SCIF or by IRQ3E

5

IRQ4

Slave

3

Drive possible in SCIF or by IRQ4E

6

IRQ5

Slave

3

Drive possible in SCIF or by IRQ5E

7

IRQ6

Slave

3

Drive possible in LPC channels 2, 3, and SCIF

8

IRQ7

Slave

3

Drive possible in SCIF or by IRQ7E

9

IRQ8

Slave

3

Drive possible in SCIF or by IRQ8E

10

IRQ9

Slave

3

Drive possible in LPC channels 2, 3, and SCIF

11

IRQ10

Slave

3

Drive possible in LPC channels 2, 3, and SCIF

12

IRQ11

Slave

3

Drive possible in LPC channels 2, 3, and SCIF

13

IRQ12

Slave

3

Drive possible in LPC channel 1 and SCIF

14

IRQ13

Slave

3

Drive possible in SCIF or by IRQ13E

15

IRQ14

Slave

3

Drive possible in SCIF or by IRQ14E

16

IRQ15

Slave

3

Drive possible in SCIF or by IRQ15E

17 IOCHCK

Slave 3

Drive

impossible

18

Stop

Host

Undefined

First, 1 or more idle states, then 2 or 3 states
0-driven by host
2 states: Quiet mode next
3 states: Continuous mode next

«
...
794
795
796
797
798
...
»

Summary of Contents for H8S Family















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S Family

Brand: TC Electronic Pages: 2

Brand: dbx Pages: 8

Brand: Panasonic Pages: 4

Brand: Lanner Pages: 109

Brand: T.A Pages: 11

Enterasys Matrix 2G4082-25

Brand: Enterasys Pages: 58

Brand: MEDIATEK Pages: 166

DL-DVI-Vision-IP Series

Brand: G&D Pages: 228

CY62136EV30 MoBL

Brand: Cypress Semiconductor Pages: 12

Brand: ZoneVu Pages: 15

Brand: FUNcube Pages: 23

Brand: mikroElektronika Pages: 2

Brand: Logicube Pages: 56

Brand: AC Infinity Pages: 24

LatticeMico GPIO

Brand: Lattice Semiconductor Pages: 28

Brand: Intel Pages: 20

Brand: Dantel Pages: 22

Brand: PairGain Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands