Renesas H8S Family Hardware Manual Download | Manualshive

Page: 843 / 1230

background image

Section 21 Ethernet Controller Direct Memory Access Controller (E-DMAC)

Rev. 1.00 Mar. 12, 2008 Page 795 of 1178

REJ09B0403-0100

Bit Bit

Name

Initial
value

R/W Description

0 SWR 0 R/W

Software

Reset

Writing 1 in this bit initializes registers of the E-DMAC
other than TDLAR, RDLAR, RMFCR, and ECBRR, and
registers of the EtherC. While a software reset is issued
(for 64 states), accesses to the all Ethernet-related
registers are prohibited.

Software reset period (example):

When

φ

= 34 MHz: 1.88

µ

s

This bit is always read as 0.

0: Writing 0 is ignored (E-DMAC operation is not

affected)

1: Writing 1 resets the EtherC and E-DMAC and then

automatically cleared

21.2.2

E-DMAC Transmit Request Register (EDTRR)

The EDTRR is a 32-bit readable/writable register that issues transmit directives to the E-DMAC.
When transmission of one frame is completed, the next descriptor is read. If the transmit
descriptor active bit in this descriptor has the "active" setting, transmission is continued. If the
transmit descriptor active bit has the "inactive" setting, the TR bit is cleared and operation of the
transmit DMAC is halted.

Bit Bit

Name

Initial
value

R/W Description

31 to 1



All

0

R

Reserved

These bits are always read as 0. The initial value
should not be changed.

0 TR 0 R/W

Transmit

Request

Check TR = 0 before transmission is started.

0: Transmission-halted state. Writing 0 does not stop

transmission. Termination of transmission is
controlled by the active bit in the transmit descriptor

1: Start of transmission. The relevant descriptor is read

and a frame is sent with the transmit active bit set to
1

«
...
841
842
843
844
845
...
»

Summary of Contents for H8S Family















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S Family

Brand: dbx Pages: 8

Brand: Accuphase Pages: 2

Brand: ADTRAN Pages: 2

AMB-VDX3H1 Series

Brand: Acrosser Technology Pages: 4

EK-FC780 GTX Jetstream

Brand: ekwb Pages: 2

NetStructure ZT 5515

Brand: Intel Pages: 90

Easy Tool-ID BSG TID-05-T30-00-005

Brand: Balluff Pages: 46

memonizerWORKSTATION

Brand: MEMON Pages: 2

Brand: NKE Pages: 15

Brand: Compro Technology Pages: 2

Brand: National Instruments Pages: 121

Brand: Zonet Pages: 1

ibaPADU-S-IT-16

Brand: IBA Pages: 80

Brand: CAMBRIONIX Pages: 43

Firebox T85-PoE

Brand: Watchguard Pages: 27

EDID 101H 4K PLUS

Brand: Extron electronics Pages: 35

CloudVision DCA-100-CV

Brand: Arista Pages: 46

Network Device PWE-4803RU

Brand: Crestron Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands