Renesas H8S Family Hardware Manual Download | Manualshive

Page: 362 / 1230

background image

Section 8 I/O Ports

Rev. 1.00 Mar. 12, 2008 Page 314 of 1178

REJ09B0403-0100

(2)

Port 8 Data Register (P8DR)

P8DR stores output data for the port 8 pins.

Bit

Bit Name

Initial Value

R/W Description

7 P87DR 0

R/W

6 P86DR 0

R/W

5 P85DR 0

R/W

4 P84DR 0

R/W

3 P83DR 0

R/W

2 P82DR 0

R/W

1 P81DR 0

R/W

0 P80DR 0

R/W

P8DR stores output data for the port 8 pins that are
used as the general output port.

If this register is read, the P8DR values are read for
the bits with the corresponding P8DDR bits set to 1.
For the bits with the corresponding P8DDR bits
cleared to 0, the pin states are read.

(3)

Pin Functions

The relationship between register setting values and pin functions are as follows.

•

P87/

ExIRQ15

/TxD3/

ADTRG

The pin function is switched as shown below according to the combination of the TE bit in
SCR of SCI_3, the SMIF bit in SCMR, and the P87DDR bit.

When the TRGS1 and EXTRGS bits are both set to 1 and the TRGS0 bit is cleared to 0 in
ADCR of the A/D converter, this pin can be used as the

ADTRG

input pin.

When the ISS15 bit in ISSR16 is set to 1, this pin can be used as the

ExIRQ15

input pin. To

use this pin as the

ExIRQ15

input pin, clear the P87DDR bit to 0.

P87DDR 0

1

SMIF 0

1

0

1

0

TE 0

X

0

X

1

P87 input pin

Pin function

ExIRQ15

input pin/

ADTRG

input pin

P87 output pin

TxD3 output pin

[Legend] X: Don't care.

«
...
360
361
362
363
364
...
»

Summary of Contents for H8S Family















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S Family

Brand: Xinje Pages: 76

Brand: CAP-XX Pages: 8

Wisenet PRN-6400B4

Brand: Hanwha Techwin Pages: 14

Brand: ZALMAN Pages: 9

Brand: 3Ware Pages: 4

Duinotech Lilypad Plus XC3920

Brand: Jaycar Electronics Pages: 2

Brand: Lutron Electronics Pages: 4

Brand: A4Tech Pages: 8

Brand: Uniden Pages: 5

Brand: ZALMAN Pages: 9

Brand: Dantel Pages: 22

PCI4-AD-x16HI-BG4

Brand: Serial Cables Pages: 15

Brand: NUROTRON Pages: 16

Brand: RAK Pages: 14

Cypress CapSense P0080

Brand: Terasic Pages: 22

Brand: Sennheiser Pages: 22

Brand: Commell Pages: 17

Brand: ESD Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands