Renesas H8S Family Hardware Manual Download | Manualshive

Page: 887 / 1230

background image

Section 22 USB Function Module (USB)

Rev. 1.00 Mar. 12, 2008 Page 839 of 1178

REJ09B0403-0100

22.3.3

Interrupt Flag Register 2 (IFR2)

IFR2, together with interrupt flag registers 0 and 1 (IFR0 and IFR1), indicates interrupt status
information required by the application. When an interrupt source is generated, the corresponding
bit is set to 1. And then this bit, in combination with interrupt enable register 2 (IER2), generates
an interrupt request to the CPU. To clear, write 0 to the bit to be cleared and 1 to the other bits.

Bit Bit

Name

Initial
Value

R/W Description

7, 6



All

0

R

Reserved

These bits are always read as 0. The initial value
should not be changed.

5 SURSS

0 R

Suspend/Resume

Status

This is a status bit that describes bus state.

0: Normal state

1: Suspended state

This bit is a status bit and generates no interrupt
request.

4 SURSF

0 R/W

Suspend/Resume

Detection

This bit is set to 1 when the state changed from normal
to suspended state or vice versa. The corresponding
interrupt output is RESUME, USBINTN2, and
USBINTN3.

3

CFDN

0

R/W

End Point Information Load End

This bit is set to 1 when writing data in the endpoint
information register to the EPIR register ends (load
end). This module starts the USB operation after the
endpoint information is completely set.

2

SOF

0

R

SOF Interrupt Detection

This bit is set to 1 when an SOF interrupt is detected.

1 SETC 0 R/W

Set_Configuration

Command

Detection

When the Set_Configuration command is detected, this
bit is set to 1.

0

SETI

0

R/W

Set_Interface Command Detection

When the Set_Interface command is detected, this bit
is set to 1.

«
...
885
886
887
888
889
...
»

Summary of Contents for H8S Family















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S Family

ShareCenter Quattro DNS-345

Brand: D-Link Pages: 40

ShareCenter Quattro DNS-345

Brand: D-Link Pages: 4

MYDLINK DNR-322L

Brand: D-Link Pages: 4

mydlink DNR-312L

Brand: D-Link Pages: 8

Brand: D-Link Pages: 16

Brand: D-Link Pages: 88

Brand: 3Com Pages: 8

Brand: Data Translation Pages: 60

Brand: Hama Pages: 4

SAFETank Series

Brand: Raidon Pages: 49

S5120V3-EI Series

Brand: H3C Pages: 54

Brand: Ublox Pages: 116

EK-FC780 GTX Jetstream

Brand: ekwb Pages: 2

Active Module Carrier VX402C-64

Brand: C&H Pages: 32

Hotwire 8775 MSDSL

Brand: Paradyne Pages: 10

Brand: axing Pages: 4

DL-DVI-Vision-IP Series

Brand: G&D Pages: 228

CY62136EV30 MoBL

Brand: Cypress Semiconductor Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands