Renesas H8S Family Hardware Manual Download | Manualshive

Page: 873 / 1230

background image

Section 21 Ethernet Controller Direct Memory Access Controller (E-DMAC)

Rev. 1.00 Mar. 12, 2008 Page 825 of 1178

REJ09B0403-0100

(b) Receive Descriptor 1 (RD1)

RD1 specifies the receive buffer length (maximum 64 kbytes).

Bit Bit

Name

Initial
value

R/W Description

31 to 16

RBL

All 0

R/W

Receive Buffer Length

These bits specify the maximum reception byte length
in the corresponding receive buffer.

The transfer byte length must align with a 16-byte
boundary (bits 19 to 16 cleared to 0). The maximum
receive frame length with one frame per buffer is
1,514 bytes, excluding the CRC data. Therefore, for
the receive buffer length specification, a value of
1,520 bytes (H'05F0) that takes account of a 16-byte
boundary is set as the maximum receive frame
length.

15 to 0

RDL

All 0

R/W

Receive Data Length

These bits specify the data length of a receive frame
stored in the receive buffer.

The receive data transferred to the receive buffer
does not include the 4-byte CRC data at the end of
the frame. The receive frame length is reported as the
number of words (valid data bytes) not including this
CRC data.

(c)

Receive Descriptor 2 (RD2)

RD2 specifies the 32-bit receive buffer start address. The receive buffer start address must be on a
longword boundary.

«
...
871
872
873
874
875
...
»

Summary of Contents for H8S Family















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S Family

OfficeConnect WX2200

Brand: 3Com Pages: 204

NetStructure ZT 5515

Brand: Intel Pages: 90

Brand: FOR-A Pages: 39

Millennium P650

Brand: Matrox Pages: 54

Brand: TANDBERG Pages: 3

Brand: QNAP Pages: 54

Brand: Aewin Technologies Pages: 86

Brand: Corsair Pages: 10

Brand: NetBurner Pages: 30

Brand: MESA Electronic Pages: 27

Brand: Allied Telesis Pages: 44

SCREENSHARE PRO

Brand: V7 Pages: 4

Brand: Foscam Pages: 92

Brand: Omron Pages: 172

Brand: Ericsson Pages: 16

Facility Explorer

Brand: Johnson Controls Pages: 33

Brand: SCT Pages: 2

Brand: Huawei Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands