Renesas H8S Family Page 578 Hardware Manual Download

Page: 578 / 1230

Section 15 Serial Communication Interface with FIFO (SCIF)

Rev. 1.00 Mar. 12, 2008 Page 530 of 1178

REJ09B0403-0100

(3) Serial Data Reception

Figure 15.5 shows an example of the data reception flowchart.

Start reception

Read DR flag in FLSR

Read FLSR

Read FRBR

Error processing

Read FLSR

DR = 1

RXFIFOERR = 1,

BI = 1, FE = 1,

PE = 1, or OE = 1

Yes

All data read

(End of reception or reception standby)

Yes

Initialization

[1]

[2]

[3]

[4]

DR = 0

[1] Confirm that the DR flag in FLSR is 1 to ensure that

receive data is in the buffer. When the OUT2 bit in

FMCR and the ERBFI bit in FIER are set to 1, a

receive data ready interrupt occurs.

[2] Read the RXFIFOERR, BI, FE, PE, and OE flags in

FLSR to ensure that no error has occurred. If an

error has occurred, perform error processing. When

the OUT2 bit in FMCR and the ELSI bit in FIER are

set to 1, a receive line status interrupt occurs.

[3] Read the receive data in FRBR.

[4] Check the DR flag in FLSR. When the DR flag is

cleared to 0 and all data has been read, data reception

complete.

Figure 15.5 Example of Data Reception Flowchart

Summary of Contents for H8S Family















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for H8S Family

Reviews:

Related manuals for H8S Family

Brands by name

Popular brands

Renesas H8S Family, Hardware Manual

Search results

Summary of Contents for H8S Family

Reviews:

Related manuals for H8S Family

Brands by name

Popular brands