Renesas H8S Family Hardware Manual Download

Page: 656 / 1230

Section 18 I

C Bus Interface (IIC)

Rev. 1.00 Mar. 12, 2008 Page 608 of 1178

REJ09B0403-0100

Bit Bit

Name

Initial
Value

R/W Description

4 AASX 0 R/(W)

Second Slave Address Recognition Flag

In I

C bus format slave receive mode, this flag is set to 1 if

the first frame following a start condition matches bits
SVAX6 to SVAX0 in SARX.

[Setting condition]

When the second slave address is detected in slave
receive mode and FSX = 0 in SARX

[Clearing conditions]

•

When 0 is written in AASX after reading AASX = 1

•

When a start condition is detected

•

In master mode

3 AL

0 R/(W)

Arbitration

Lost

Flag

Indicates that arbitration was lost in master mode.

[Setting conditions]

When ALSL=0

•

If the internal SDA and SDA pin disagree at the rise of

SCL in master transmit mode

•

If the internal SCL line is high at the fall of SCL in

master mode

When ALSL=1

•

If the internal SDA and SDA pin disagree at the rise of

SCL in master transmit mode

•

If the SDA pin is driven low by another device before

the I

C bus interface drives the SDA pin low, after the

start condition instruction was executed in master

transmit mode

[Clearing conditions]

•

When ICDR is written to (transmit mode) or read from

(receive mode)

•

When 0 is written in AL after reading AL = 1

Summary of Contents for H8S Family















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for H8S Family

Reviews:

Related manuals for H8S Family

Brands by name

Popular brands

Renesas H8S Family, Hardware Manual

Search results

Summary of Contents for H8S Family

Reviews:

Related manuals for H8S Family

Brands by name

Popular brands