Renesas H8S Family Hardware Manual Download | Manualshive

Page: 799 / 1230

background image

Section 19

LPC Interface (LPC)

Rev. 1.00 Mar. 12, 2008 Page 751 of 1178

REJ09B0403-0100

19.5.2

SMI, HIRQ1, HIRQ3, HIRQ4, HIRQ5, HIRQ6, HIRQ7, HIRQ8, HIRQ9,

HIRQ10, HIRQ11, HIRQ12, HIRQ13, HIRQ14, and HIRQ15

The LPC interface can request 15 kinds of host interrupt by means of SERIRQ. HIRQ1 and
HIRQ12 are used on LPC channel 1, while SMI, HIRQ6, HIRQ9, HIRQ10, and HIRQ11 can be
requested from LPC channels 2 and 3. For the SCIF, any one of 15 types of interrupts can be
selected. In addition, by the setting of SCIFCR4, the SCIF can request eight types of host
interrupts: HIRQ3, HIRQ4, HIRQ5, HIRQ7, HIRQ8, HIRQ13, HIRQ14, and HIRQ15.

There are two ways of clearing a host interrupt request when the LPC channels are used.

When the IEDIR bit in SIRQCR0is cleared to 0, host interrupt sources and LPC channels are all
linked to the host interrupt request enable bits. When the OBF flag is cleared to 0 by a read of
ODR or TWR15 by the host in the corresponding LPC channel, the corresponding host interrupt
enable bit is automatically cleared to 0, and the host interrupt request is cleared.

When the IEDIR bit is set to 1 in SIRQCR, a host interrupt is only requested by the host interrupt
enable bits. The host interrupt enable bit is not cleared when OBF is cleared. Therefore, SMIE2,
SMIE3A, SMIE3B, SMIE4 and IRQ6En, IRQ9En, IRQ10En, IRQ11En lose their respective
functional differences (n = 2, 3). In order to clear a host interrupt request, it is necessary to clear
the host interrupt enable bit. As for HIRQ3 to HIRQ5, HIRQ7, HIRQ8, and HIRQ13 to HIRQ15,
setting the enable bit in SIRQCR4 to 1 requests the corresponding host interrupt, and clearing the
enable bit to 0 clears the corresponding host interrupt request.

When the SCIF channels are used, a host interrupt request is cleared when the relevant SCIF
interrupt is cleared.

Table 19.12 summarizes the methods of setting and clearing these bits when the LPC channels are
used, and table 19.13 summarizes the methods of setting and clearing these bits when the SCIF
channels are used. Figure 19.12 shows the processing flowchart.

«
...
797
798
799
800
801
...
»

Summary of Contents for H8S Family















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S Family

Brand: C4i Pages: 8

Brand: IBASE Technology Pages: 71

Brand: Net to Net Technologies Pages: 4

Brand: Telex Communications Pages: 28

Brand: Qlogic Pages: 8

Brand: ZALMAN Pages: 5

RouterBOARD 411R

Brand: 4gon Pages: 2

Brand: AXAGO Pages: 2

Brand: Patton electronics Pages: 145

500 - DATASHEET REV 003

Brand: Intel Pages: 67

Brand: Hama Pages: 25

Brand: V-Count Pages: 2

DataFire GO! PRO

Brand: Digi Pages: 20

AdvancedTCA AT8901M

Brand: Kontron Pages: 76

ROADRECORDER 8400 NVR

Brand: Safety Vision Pages: 27

Wisenet XRN-6410DB4

Brand: Hanwha Techwin Pages: 118

IQ Switch ProxSense RS100

Brand: Azoteq Pages: 9

Brand: National Instruments Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands