manualshive.com logo in svg

Freescale Semiconductor MK22FN256VDC12, Reference Manual

The Freescale Semiconductor MK22FN256VDC12 is a high-performance microcontroller ideal for various applications. You can easily access the Reference Manual and user manuals for free download from manualshive.com. Get detailed information on features, specifications, and programming instructions to maximize the potential of this versatile semiconductor product.

Share
Download
background image

Timer n

Timer 1

PIT 
registers

Peripheral bus

load_value

 

PIT

Triggers

 

 

 

 

Peripheral

 

bus clock

Interrupts

 

Figure 39-1. Block diagram of the PIT

NOTE

See the chip-specific PIT information for the number of PIT
channels used in this MCU.

39.1.2 Features

The main features of this block are:

• Ability of timers to generate DMA trigger pulses

• Ability of timers to generate interrupts

• Maskable interrupts
• Independent timeout periods for each timer

39.2 Signal description

The PIT module has no external pins.

Signal description

K22F Sub-Family Reference Manual , Rev. 3, 7/2014

950

Freescale Semiconductor, Inc.

Summary of Contents for MK22FN256VDC12


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MK22FN256VDC12

Parasound 7100 Owner'S Manual preview
7100
Brand: Parasound Pages: 72
G1SLE MK2 Alignment Manual preview
MK2
Brand: G1SLE Pages: 2
GAUGEMASTER COMBI Manual preview
COMBI
Brand: GAUGEMASTER Pages: 2
EasyIO FC Series Firmware Upgrade User Manual preview
FC Series
Brand: EasyIO Pages: 19
PAC 212 Install Manual preview
212
Brand: PAC Pages: 17
Danfoss VLT AutomationDrive FC 302 Installation Manual preview
VLT AutomationDrive FC 302
Brand: Danfoss Pages: 128
Rain Bird ESP-LXD Installation, Programming & Operation Manual preview
ESP-LXD
Brand: Rain Bird Pages: 138
Jetter 60873050 Manual preview
60873050
Brand: Jetter Pages: 24
Fuji Electric FD5000 series Instruction Manual preview
FD5000 series
Brand: Fuji Electric Pages: 12
Invertek Optidrive Elevator Quick Start Up Manual preview
Optidrive Elevator
Brand: Invertek Pages: 5
Techtrol TLIC Instruction And Programming Manual preview
TLIC
Brand: Techtrol Pages: 4
Rheem RXMD-B04 Installation Instructions preview
RXMD-B04
Brand: Rheem Pages: 2
UCS SYNCHRO QUASAR AC User Manual preview
SYNCHRO QUASAR AC
Brand: UCS Pages: 10
Curtis MultiMode 1214-8 Manual preview
MultiMode 1214-8
Brand: Curtis Pages: 41
TAC Xenta 102 Handbook preview
Xenta 102
Brand: TAC Pages: 76
Velleman CHLSC2 User Manual preview
CHLSC2
Brand: Velleman Pages: 22
National Instruments NI 9683 User Manual And Specifications preview
NI 9683
Brand: National Instruments Pages: 27
TE Connectivity AMP 3K/40 CE 2161600-1 Original Instructions Manual preview
AMP 3K/40 CE 2161600-1
Brand: TE Connectivity Pages: 29

Brands by name

Popular brands

Load more brands