Freescale Semiconductor MK22FN256VDC12 Reference Manual Download Page 560 | Manualshive

Page: 560 / 1313

background image

The table below shows MCGOUTCLK frequency calculations using C1[FRDIV],
C5[PRDIV0], and C6[VDIV0] settings for each clock mode.

Table 25-17. MCGOUTCLK Frequency Calculation Options

Clock Mode

f

MCGOUTCLK

Note

FEI (FLL engaged internal)

(f

int

* F)

Typical f

MCGOUTCLK

= 21 MHz

immediately after reset.

FEE (FLL engaged external)

(f

ext

/ FLL_R) *F

f

ext

/ FLL_R must be in the range of

31.25 kHz to 39.0625 kHz

FBE (FLL bypassed external)

OSCCLK

OSCCLK / FLL_R must be in the
range of 31.25 kHz to 39.0625 kHz

FBI (FLL bypassed internal)

MCGIRCLK

Selectable between slow and fast
IRC

PEE (PLL engaged external)

(OSCCLK / PLL_R) * M

OSCCLK / PLL_R must be in the
range of 2 – 4 MHz

PBE (PLL bypassed external)

OSCCLK

OSCCLK / PLL_R must be in the
range of 2 – 4 MHz

BLPI (Bypassed low power internal)

MCGIRCLK

Selectable between slow and fast
IRC

BLPE (Bypassed low power external)

OSCCLK

1. FLL_R is the reference divider selected by the C1[FRDIV] bits, PLL_R is the reference divider selected by C5[PRDIV0]

bits, F is the FLL factor selected by C4[DRST_DRS] and C4[DMX32] bits, and M is the multiplier selected by C6[VDIV0]
bits.

This section will include three mode switching examples using an 4 MHz external
crystal. If using an external clock source less than 2 MHz, the MCG must not be
configured for any of the PLL modes (PEE and PBE).

25.5.3.1 Example 1: Moving from FEI to PEE mode: External Crystal =

4 MHz, MCGOUTCLK frequency = 48 MHz

In this example, the MCG will move through the proper operational modes from FEI to
PEE to achieve 48 MHz MCGOUTCLK frequency from 4 MHz external crystal
reference. First, the code sequence will be described. Then there is a flowchart that
illustrates the sequence.

1. First, FEI must transition to FBE mode:

a. C2 = 0x2C

• C2[RANGE] set to 2'b01 because the frequency of 4 MHz is within the high

frequency range.

Initialization / Application information

K22F Sub-Family Reference Manual , Rev. 3, 7/2014

560

Freescale Semiconductor, Inc.

«
...
558
559
560
561
562
...
»

Summary of Contents for MK22FN256VDC12


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MK22FN256VDC12

Brand: QCON Pages: 4

Brand: IFM Pages: 49

Brand: L-Acoustics Pages: 24

Brand: L-Acoustics Pages: 21

Brand: IBM Pages: 214

Brand: YASKAWA Pages: 340

Brand: AirCycler Pages: 2

Torque Converter Lock-Up

Brand: TS Performance Pages: 4

STRATOSTM INSPIRE

Brand: Ultrahaptics Pages: 7

Brand: M-Elec Pages: 2

ACTPRO PRODUCT RANGE

Brand: ACT Pages: 8

Brand: WAC Pages: 5

Raptor S-Tower F4-20A

Brand: Flycolor Pages: 2

Brand: ITRON Pages: 24

SYG-S7G2-43C-MDK

Brand: FDI Pages: 28

Brand: Pulse Instruments Pages: 134

DALI PRO CONT-4 RTC

Brand: Osram Pages: 4

Brand: YASKAWA Pages: 455

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands