manualshive.com logo in svg

Freescale Semiconductor MK22FN256VDC12, Reference Manual

The Freescale Semiconductor MK22FN256VDC12 is a high-performance microcontroller ideal for various applications. You can easily access the Reference Manual and user manuals for free download from manualshive.com. Get detailed information on features, specifications, and programming instructions to maximize the potential of this versatile semiconductor product.

Share
Download
background image

36.3.1 Voltage Reference Disabled, SC[VREFEN] = 0

When SC[VREFEN] = 0, the Voltage Reference is disabled, the VREF bandgap and the
output buffers are disabled. The Voltage Reference is in off mode.

36.3.2 Voltage Reference Enabled, SC[VREFEN] = 1

When SC[VREFEN] = 1, the Voltage Reference is enabled, and different modes should
be set by the SC[MODE_LV] bits.

36.3.2.1 SC[MODE_LV]=00

The internal VREF bandgap is enabled to generate an accurate 1.2 V output that can be
trimmed with the TRM register's TRIM[5:0] bitfield. The bandgap requires some time for
startup and stabilization. SC[VREFST] can be monitored to determine if the stabilization
and startup is complete when the chop oscillator is not enabled.

If the chop oscillator is being used, the internal bandgap reference voltage settles within
the chop oscillator start up time, Tchop_osc_stup.

The output buffer is disabled in this mode, and there is no buffered voltage output. The
Voltage Reference is in standby mode. If this mode is first selected and the low power or
high power buffer mode is subsequently enabled, there will be a delay before the buffer
output is settled at the final value. This is the buffer start up delay (Tstup) and the value is
specified in the appropriate device data sheet.

36.3.2.2 SC[MODE_LV] = 01

The internal VREF bandgap is on. The high power buffer is enabled to generate a
buffered 1.2 V voltage to VREF_OUT. It can also be used as a reference to internal
analog peripherals such as an ADC channel or analog comparator input.

If this mode is entered from the standby mode (SC[MODE_LV] = 00, SC[VREFEN] = 1)
there will be a delay before the buffer output is settled at the final value. This is the buffer
start up delay (Tstup) and the value is specified in the appropriate device data sheet. If
this mode is entered when the VREF module is enabled then you must wait the longer of

Chapter 36 Voltage Reference (VREFV1)

K22F Sub-Family Reference Manual , Rev. 3, 7/2014

Freescale Semiconductor, Inc.

791

Summary of Contents for MK22FN256VDC12


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MK22FN256VDC12

Danfoss VLT series Quick Manual preview
VLT series
Brand: Danfoss Pages: 37
Vega VEGAMET 141 Operating Instructions Manual preview
VEGAMET 141
Brand: Vega Pages: 20
Eaton Cutler-Hammer LMR Instructions Manual preview
Cutler-Hammer LMR
Brand: Eaton Pages: 38
YASKAWA Z1000 CIMR-ZU*A Series Programming Manual preview
Z1000 CIMR-ZU*A Series
Brand: YASKAWA Pages: 340
ETC Echoflex ELED2 Installation Manual preview
Echoflex ELED2
Brand: ETC Pages: 8
Texas Instruments MSP430F67681 Manual preview
MSP430F67681
Brand: Texas Instruments Pages: 27
Espressif Systems ESP32-DevKitC Getting Started Manual preview
ESP32-DevKitC
Brand: Espressif Systems Pages: 11
DPS Telecom NetGuardian LPG D-PK-NGLPG User Manual preview
NetGuardian LPG D-PK-NGLPG
Brand: DPS Telecom Pages: 82
Suzhou Lily ZL-7901A Instruction Manual preview
ZL-7901A
Brand: Suzhou Lily Pages: 8
Cypress CY3280-20x66 Universal CapSense Quick Start Manual preview
CY3280-20x66 Universal CapSense
Brand: Cypress Pages: 2
Pulsafeeder MicroVision EX User Manual preview
MicroVision EX
Brand: Pulsafeeder Pages: 24
Eaton EM4-201-DX2 Installation Instructions Manual preview
EM4-201-DX2
Brand: Eaton Pages: 9
Watt Stopper DRD6 v2 Installation Instructions preview
DRD6 v2
Brand: Watt Stopper Pages: 3
MRC TECH 6 2.0 Quick Start Manual preview
TECH 6 2.0
Brand: MRC Pages: 2
Lemona 70200051 Quick Start Manual preview
70200051
Brand: Lemona Pages: 3
Omega CNi16A User Manual preview
CNi16A
Brand: Omega Pages: 73
Abov MC96FM204 User Manual preview
MC96FM204
Brand: Abov Pages: 172
Zenpro SmartControl ZSC1 Manual preview
SmartControl ZSC1
Brand: Zenpro Pages: 34

Brands by name

Popular brands

Load more brands