Freescale Semiconductor MK22FN256VDC12 Reference Manual Download Page 1138 | Manualshive

Page: 1138 / 1313

background image

UART memory map (continued)

Absolute

address

(hex)

Register name

Width

(in bits)

Access Reset value

Section/

page

4006_C01A UART 7816 Interrupt Status Register (UART2_IS7816)

8

R/W

00h

4006_C01B UART 7816 Wait Parameter Register (UART2_WP7816)

8

R/W

00h

4006_C01C UART 7816 Wait N Register (UART2_WN7816)

8

R/W

00h

4006_C01D UART 7816 Wait FD Register (UART2_WF7816)

8

R/W

01h

4006_C01E UART 7816 Error Threshold Register (UART2_ET7816)

8

R/W

00h

4006_C01F UART 7816 Transmit Length Register (UART2_TL7816)

8

R/W

00h

4006_C03A

UART 7816 ATR Duration Timer Register A
(UART2_AP7816A_T0)

8

R/W

00h

4006_C03B

UART 7816 ATR Duration Timer Register B
(UART2_AP7816B_T0)

8

R/W

00h

4006_C03C

UART 7816 Wait Parameter Register A
(UART2_WP7816A_T0)

8

R/W

00h

4006_C03C

UART 7816 Wait Parameter Register A
(UART2_WP7816A_T1)

8

R/W

00h

4006_C03D

UART 7816 Wait Parameter Register B
(UART2_WP7816B_T0)

8

R/W

14h

4006_C03D

UART 7816 Wait Parameter Register B
(UART2_WP7816B_T1)

8

R/W

14h

4006_C03E

UART 7816 Wait and Guard Parameter Register
(UART2_WGP7816_T1)

8

R/W

06h

4006_C03F

UART 7816 Wait Parameter Register C
(UART2_WP7816C_T1)

8

R/W

0Bh

46.3.1 UART Baud Rate Registers: High (UARTx_BDH)

This register, along with the BDL register, controls the prescale divisor for UART baud
rate generation. To update the 13-bit baud rate setting (SBR[12:0]), first write to BDH to
buffer the high half of the new value and then write to BDL. The working value in BDH
does not change until BDL is written.

BDL is reset to a nonzero value, but after reset, the baud rate generator remains disabled
until the first time the receiver or transmitter is enabled, that is, when C2[RE] or C2[TE]
is set.

Memory map and registers

K22F Sub-Family Reference Manual , Rev. 3, 7/2014

1138

Freescale Semiconductor, Inc.

«
...
1136
1137
1138
1139
1140
...
»

Summary of Contents for MK22FN256VDC12


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MK22FN256VDC12

Brand: QCON Pages: 4

Brand: OMC Pages: 18

Brand: GEM Pages: 17

Brand: Cardin Elettronica Pages: 56

Brand: Festo Pages: 87

WFHC 06Z 02 HC RF 24

Brand: Watts Pages: 18

Errata MSP430F6779

Brand: Texas Instruments Pages: 27

MAXinBOX 24 ZIO-MB24

Brand: Zennio Pages: 24

WISE-224 Series

Brand: ICP DAS USA Pages: 8

Brand: ICStation Pages: 3

MODACT MTNED 15

Brand: ZPA Pecky, a.s. Pages: 48

Brand: YASKAWA Pages: 348

Brand: Knoll Pages: 2

Brand: Hanbay Pages: 13

SetPro MV Series

Brand: Gigarise Pages: 18

Brand: Inner Range Pages: 28

EDGEIQ EE-202-0050

Brand: Edge Electrons Pages: 32

BaseStation 1000

Brand: Base Line Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands