manualshive.com logo in svg

Freescale Semiconductor MK22FN256VDC12, Reference Manual

The Freescale Semiconductor MK22FN256VDC12 is a high-performance microcontroller ideal for various applications. You can easily access the Reference Manual and user manuals for free download from manualshive.com. Get detailed information on features, specifications, and programming instructions to maximize the potential of this versatile semiconductor product.

Share
Download
background image

26.10 Low power modes operation

When the MCU enters Stop modes, the OSC is functional depending on CR[ERCLKEN]
and CR[EREFSETN] bit settings. If both these bits are set, the OSC is in operation.

In Low Leakage Stop (LLS) modes, the OSC holds all register settings. If
CR[ERCLKEN] and CR[EREFSTEN] are set before entry to Low Leakage Stop modes,
the OSC is still functional in these modes. After waking up from Very Low Leakage Stop
(VLLSx) modes, all OSC register bits are reset and initialization is required through
software.

26.11 Interrupts

The OSC module does not generate any interrupts.

Low power modes operation

K22F Sub-Family Reference Manual , Rev. 3, 7/2014

580

Freescale Semiconductor, Inc.

Summary of Contents for MK22FN256VDC12


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MK22FN256VDC12

Microchip Technology PLECS Quick Start Manual preview
PLECS
Brand: Microchip Technology Pages: 37
Galaxy Control Systems 635 Series Worksheet preview
635 Series
Brand: Galaxy Control Systems Pages: 5
QED MP50 Instruction Manual preview
MP50
Brand: QED Pages: 26
Tech 21 MIDI MONGOOSE Owner'S Manual preview
MIDI MONGOOSE
Brand: Tech 21 Pages: 2
TEL AFA4000/1/AS Installation And Calibration Manual preview
AFA4000/1/AS
Brand: TEL Pages: 26
Vimar EAM6 Installation And Operation Manual preview
EAM6
Brand: Vimar Pages: 32
Frico ERP Instruction Manual preview
ERP
Brand: Frico Pages: 12
Forcepoint C1015 Hardware Manual preview
C1015
Brand: Forcepoint Pages: 15
SMC Networks JAS-L Series Operation Manual preview
JAS-L Series
Brand: SMC Networks Pages: 12
KBR multicomp F144-MS-1V1C1TI6RO-3 User Manual preview
multicomp F144-MS-1V1C1TI6RO-3
Brand: KBR Pages: 68
Powtran PR5200 Series Manual preview
PR5200 Series
Brand: Powtran Pages: 36
NI cRIO-9065 Features preview
cRIO-9065
Brand: NI Pages: 28
Altronic DE-2500 Installation & Operating Instructions Manual preview
DE-2500
Brand: Altronic Pages: 70
A.O. Smith INTELLI-VENT Troubleshooting Manual preview
INTELLI-VENT
Brand: A.O. Smith Pages: 46
Phocos CIS05-2L User Manual preview
CIS05-2L
Brand: Phocos Pages: 2
Bernard Controls AQ Logic Series Startup Manual preview
AQ Logic Series
Brand: Bernard Controls Pages: 88
Lintec MC-3000L-TC Series Instruction Manual preview
MC-3000L-TC Series
Brand: Lintec Pages: 2
Xylem CentriPro SPD Plus Instruction Manual preview
CentriPro SPD Plus
Brand: Xylem Pages: 36

Brands by name

Popular brands

Load more brands