Error solving manual.
CNC 8060
CNC 8065
·125·
(R
EF
: 1709)
3047
'M3/M4/M5/M19/M41-M44 not allowed while G63 is active'
DETECTION
During execution.
CAUSE
After interrupting a program having G63 active and changing to MHFS mode, the user
has edited an M3, M4, M5, M19 or M41 through M44 that is not allowed for G63.
SOLUTION
Cancel function G63 or wait until this function is completed before interrupting the
program.
3048
'The programmed gear does not exist'
DETECTION
During execution.
CAUSE
After interrupting a program and changing to MHFS mode, the user has edited an
M function associated with a gear that does not exist in the channel.
SOLUTION
Program the right gear.
3050
'The S cannot be changed if the spindle works as C axis'
DETECTION
During execution.
CAUSE
The user has tried to change the speed of a spindle that is active as C axis.
SOLUTION
Program a feedrate F for the C axis or cancel it to program a speed.
3051
'Incompatible M functions for the same spindle'
DETECTION
During execution.
CAUSE
After interrupting a program and changing to MHFS mode, the user has edited some
functions M3, M4, M5, M19 or M41 through M44 that are incompatible for the same
spindle.
SOLUTION
Decide which M function to execute or execute one after the other, but not at the same
time.
3052
'The spindle status must be the same as the one at the time of the interruption'
DETECTION
During execution.
CAUSE
After interrupting a program and changing to MHFS mode, the user tries to exit this
mode while the spindle is in an M3, M4, M5 or M19 state different from the initial one.
SOLUTION
Program a new spindle state change so it gets into the same state as before the
interruption.
3056
'Error when calculating the reverse transformation of the incline axis #ANGAX'
DETECTION
During execution.
CAUSE
In an angular transformation, the incline axis and the orthogonal axis form a 90º angle.
SOLUTION
The angular transformation is not necessary; cancel the transformation with the
instruction #ANGAX OFF.
3057
'Error when calculating the direct transformation of the incline axis #ANGAX'
DETECTION
During execution.
CAUSE
In an angular transformation, the incline axis and the orthogonal axis form a 90º angle.
SOLUTION
The angular transformation is not necessary. Cancel the angular transformation
#ANGAX OFF.
3058
'Spindle functions M3/M4/M5/M19 and M41-M44 must be sent out to the PLC'
DETECTION
During execution.
CAUSE
After a block search and before resuming the execution of the program, the CNC has
detected that some function of the spindle has not been sent to the PLC.
SOLUTION
The program being interrupted, switch to MHFS mode and send the necessary
functions to the PLC.
3059
'M3/M4/M5/M19/M41-M44 not allowed while M19 or G74 is active'
DETECTION
During execution.
CAUSE
The user has interrupted the program during the execution of M19 or G74 at a spindle.
The CNC cannot send functions M3/M4/M5/M19 and M41-M44 out to the spindle.
SOLUTION
Go on with the execution until function M19 or G74 is completed. Then, interrupt the
program and send the desired functions to the spindle.
3060
'The S value cannot exceed the programmed gear'
DETECTION
During execution.
CAUSE
After interrupting a program and changing to MHFS mode, the user has programmed
a speed and a new gear, and the speed is higher than the maximum for that gear.
SOLUTION
Change the programmed speed or gear or program only one of them so they don't
contradict each other.
Summary of Contents for 8065
