Error solving manual.
CNC 8060
CNC 8065
·158·
(R
EF
: 1709)
6014
'Failed access to DPRAM of the COMPCI'
DETECTION
During execution.
CAUSE
Failed access to the common RAM memory of the COMPCI due to hardware error,
bad contact, etc. The CNC and the COMPCI run Read/Write tests of the common
RAM on start-up and cyclically.
SOLUTION
The diagnosis mode offers additional information about the failure. Contact our
technical service department.
6015
'CAN error counter exceeded level 1'
DETECTION
During execution.
CAUSE
The (Rx/Tx) error frame counter exceeds level 1 (96).
SOLUTION
Make the relevant checks to assure the integrity of the CAN bus. If the error persists,
contact the Service Department.
6016
'CAN error counter at a critical level'
DETECTION
During execution.
CAUSE
The (Rx/Tx) error frame counter exceeds the critical level (127).
SOLUTION
Make the relevant checks to assure the integrity of the CAN bus. If the error persists,
contact the Service Department.
6017
'CAN controller's FIFO overrun'
DETECTION
During execution.
CAUSE
Overflow at the CAN controller's receiving FIFO. Possible loss of received messaged.
SOLUTION
Contact our technical service department.
6018
'COMPCI's FIFO CAN overrun'
DETECTION
During execution.
CAUSE
Overflow at the COMPCI's receiving FIFO. Possible loss of received messaged.
SOLUTION
Contact our technical service department.
6019
'CAN reading timeout'.
DETECTION
During execution.
CAUSE
Failed cyclic reading of digital and analog inputs, counters and keyboard handwheels.
A node did not send the message in time.
SOLUTION
Check in diagnosis mode that the CNC recognizes all the modules and the CAN error
counter; if there are errors, run the pertinent checks to ensure the integrity of the CAN
bus. If necessary, increase the cycle times (parameters LOOPTIME and PLCFREQ).
If the error persists, contact the Service Department.
6020
'CAN cycle overlap'
DETECTION
During execution.
CAUSE
Failed cyclic reading of digital and analog inputs, counters and keyboard handwheels.
A node did not send the message in time.
SOLUTION
Check in diagnosis mode that the CNC recognizes all the modules and the CAN error
counter; if there are errors, run the pertinent checks to ensure the integrity of the CAN
bus. If necessary, increase the cycle times (parameters LOOPTIME and PLCFREQ).
If the error persists, contact the Service Department.
6021
'Problems in CAN transmission'
DETECTION
During execution.
CAUSE
Failed transmission of digital and analog outputs, etc. Possible bus collapse.
SOLUTION
Check in diagnosis mode that the CNC recognizes all the modules and the CAN error
counter; if there are errors, run the pertinent checks to ensure the integrity of the CAN
bus. If necessary, increase the cycle times (parameters LOOPTIME and PLCFREQ).
If the error persists, contact the Service Department.
6022
'Error when initializing the Axis counter'
DETECTION
During CNC startup.
CAUSE
The counter does not exist. The error window indicates which counter is causing the
error.
SOLUTION
Check the machine parameters. If the error persists, contact the Service Department.
Summary of Contents for 8065
