Error solving manual.
CNC 8060
CNC 8065
·116·
(R
EF
: 1709)
2392
Linear zone: The lower limit must be smaller that than the upper limit for each axis'
DETECTION
During block preparation.
CAUSE
The CNC has tried to enable a work zone where the lower limit of an axis is greater
than the upper limit.
SOLUTION
In a linear zone, the lower limit of the axis must be smaller than the upper limit. Change
the lower limit (G120) or the higher limit (G121) of the axis. Checking is not carried
out if the zone is disabled.
2393
'E function programmed twice'
DETECTION
During block preparation.
CAUSE
The "E" parameter has been programmed more than once in the same block.
SOLUTION
Program the "E" parameter only once in the block.
2394
'G122: Work zone status not programmed'
DETECTION
During block preparation.
CAUSE
The work zone status has not been programmed in G122.
SOLUTION
Program the work zone status in parameter "E"; from 0 to 2.
2395
'The center cannot be programmed with module-type rotary axes'
DETECTION
During execution.
CAUSE
The center cannot be programmed with module-type rotary axes.
SOLUTION
The center cannot be defined with module-type rotary axes. Check the program.
2400
'Logic number of the axis out of range'
DETECTION
During execution.
CAUSE
The programmed logic number is wrong.
SOLUTION
Program a correct logic axis; from 1 to NAXIS.
2401
'#FREE/SET AX: An axis that defines an active work zone cannot be freed (released)'
DETECTION
During execution.
CAUSE
The CNC has tried to remove from the configuration an axis that is part of an active
work zone.
SOLUTION
Deactivate the work zone before freeing (releasing) the axis.
2402
'#PARK: An axis that defines an active work zone cannot be parked'
DETECTION
During execution.
CAUSE
The CNC has tried to park an axis that is part of an active work zone.
SOLUTION
Deactivate the work zone before parking the axis.
2403
'A zone cannot be activated while one of its axes is parked'
DETECTION
During execution.
CAUSE
The CNC has tried to activate a work zone; but one of the axes that define it is parked.
SOLUTION
Unpark the axis before activating the work zone.
2404
#GAPCTRL: The index has been changed for the controlled axis channel.
DETECTION
During block preparation.
CAUSE
The possible causes are:
• When the active gap control (#GAPCTRL ON) is on, an instruction is programmed
that changes the index for that axis in the channel (#SET AX, #CALL AX, #FREE
AX).
• If the machine parameter GAPCTRLCANCEL is set to "NO", the axis remains
controlled after the program has finished or following a reset. This error persists
if the axis index has been changed under these conditions.
SOLUTION
It is not possible to modify the position of the axes in the channel with the active gap
control.
2405
Movement block canceled because an axis has #GAPCTRL.
DETECTION
During tool inspection or MDI mode.
CAUSE
An attempt has been made to move an axis in MDI that is being controlled by the
command #GAPCTRL.
SOLUTION
Program #GAPCTRL OFF.
Summary of Contents for 8065
