Fagor 8065 Error Solving Manual Download | Manualshive

Page: 208 / 220

background image

Error solving manual.

CNC 8060
CNC 8065

·208·

(R

EF

: 1709)

RCS-S MODULE.

E034

Error identifying the CPU board.

Contact Fagor Automation.

E038

Code checksum error.

The loaded checksum of the program code is not correct. Load the software again. If the problem persists, the RAM,
FLASH memories or the loaded code may be defective. Contact Fagor Automation.

E039

Error on the Sercos ® board .

Contact Fagor Automation.

E040

Failure of the clock of the SerCon® board.

Contact Fagor Automation.

E041

SerCon memory corrupted.

Contact Fagor Automation.

E044

Corrupted file system in flash.

Contact Fagor Automation.

E045

Error reading analog offsets.

Contact Fagor Automation.

E046

Error identifying the axis board.

Contact Fagor Automation.

E047

Unknown axis board identification.

Contact Fagor Automation.

E04

Error in FPGA code.

The FPGA code seems to be corrupted or is missing. Try reloading the software version. If the problem persists, the
RAM, FLASH memories or the loaded code may be defective. Contact Fagor Automation.

E083

The FPGA could not be loaded.

Restart the counter. If the problem persists, contact Fagor Automation.

E084

Reset due to Watchdog.

The system has restarted because watchdog kicked in. If the problem is repetitive and/or persists, contact Fagor
Automation.

E085

Error in power supply for the analog outputs.

Contact Fagor Automation.

E133

Broken wire, A signal of E21A feedback.

E233

Broken wire, A signal of E21B feedback.

E333

Broken wire, A signal of E21C feedback.

E433

Broken wire, A signal of E21D feedback.

For differential TTL feedback. The A and/or /A signal wire may be broken or disconnected.
Check the connection. Check the level of the signals provided by the feedback device.

E134

Broken wire, B signal of E21A feedback.

E234

Broken wire, B signal of E21B feedback.

E334

Broken wire, B signal of E21C feedback.

E434

Broken wire, B signal of E21D feedback.

For differential TTL feedback. The B and/or /B signal wire may be broken or disconnected.
Check the connection. Check the level of the signals provided by the feedback device.

E135

Broken wire, I0 signal of E21A feedback.

E235

Broken wire, I0 signal of E21B feedback.

E335

Broken wire, I0 signal of E21C feedback.

«
...
206
207
208
209
210
...
»

Summary of Contents for 8065





























































































































































































































Reviews:

No comments

Related manuals for 8065

Brand: Ransburg Pages: 49

Brand: Balboa Pages: 2

Brand: Badger Meter Pages: 20

Brand: Tapeswitch Pages: 13

Brand: YASKAWA Pages: 256

Brand: Daikin Pages: 5

Brand: Veeder-Root Pages: 27

Brand: Valve Concepts Pages: 18

Brand: K&K Pages: 6

Brand: Zennio Pages: 30

Brand: Zeta Pages: 13

Brand: V2 Pages: 12

NORA-W10 Series

Brand: u-blox Pages: 56

Brand: z21 Pages: 2

Brand: Pacostar Pages: 55

Brand: Zepro Pages: 64

Brand: AzureWave Pages: 21

AMP 3K/40 CE 2161600-1

Brand: TE Connectivity Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands