Error solving manual.
CNC 8060
CNC 8065
·118·
(R
EF
: 1709)
2415
PWCTRL OUT not allowed without master spindle in the channel.
DETECTION
During execution.
CAUSE
The power control is applied to the master spindle. An attempt was made to activate
the power control and there is no master spindle active.
SOLUTION
Select a master spindle (# MASTER) before activating the power control.
2416
#PWRCTRL ON [<DUTY/D/OUT/O> <,OVRMINvalue> <,OVRMAXvalue> <,FMINvalue>
<,FMAXvalue>]
DETECTION
During editing and execution.
CAUSE
The syntax of the instruction is wrong.
SOLUTION
Check the syntax of the instruction in the programming manual.
2417
#PWRCTRL ON: FMIN must be less than FMAX.
DETECTION
During execution.
CAUSE
For the function #PWRCTRL, the minimum feedrate is greater than the maximum
feedrate.
SOLUTION
The minimum feedrate (FZMIN) must be less than the maximum feedrate (FZMAX).
2418
#PWRCTRL ON: OVRMIN must be less than OVRMAX.
DETECTION
During execution.
CAUSE
For the function #PWRCTRL, the minimum override is greater than the maximum
override.
SOLUTION
The minimum override (OVRMIN) must be less than the maximum override
(OVRMAX).
2419
#PWRCTRL ON: the first time, all parameters must be programmed.
DETECTION
During execution.
CAUSE
The function #PWRCTRL has been programmed for the first time and a parameter
is missing.
SOLUTION
The function #PWRCTRL has been programmed for the first time and all parameters
must be programmed.
2420
#FOLLOW ON[MASTER, ]. The slave axis cannot be the slave of another master.
DETECTION
During execution.
CAUSE
The slave axis for the synchronization is already a slave for another synchronization.
SOLUTION
An axis cannot be the slave for two synchronizations.
2421
The master spindle cannot be changed or parked while PWRCTRL is active.
DETECTION
During execution.
CAUSE
The master spindle cannot be changed or parked while PWRCTRL is active.
SOLUTION
The power control is applied to the master spindle. To change or park the master
spindle, deactivate the power control (#PWRCTRL).
2422
#TFOLLOW ON [MASTER] is not permitted. Permitted: #FOLLOW ON [MASTER]
DETECTION
During block preparation.
CAUSE
When an axis is programmed to be slave for the variable FLWMASTER, the
synchronization can only done using real coordinates; it is not possible to synchronize
theoretical coordinates.
SOLUTION
Perform a synchronization with real coordinates.
2423
Undefined #CUTTING or #PIERCING type.
DETECTION
During block preparation.
CAUSE
The type of piercing or cutting is zero. The parameter T is missing in the instruction
and a T (type) value has not been previously programmed.
SOLUTION
Activate a technological table, program the material command or program the
command #PIERCING or #CUTTING generating the error with a correct T parameter
(value between 1 and 10).
2424
No active technological table (#MATERIAL).
DETECTION
During block preparation.
CAUSE
The command #PIERCING and #CUTTING have been programmed and there is no
technological table active.
SOLUTION
Activate a technological table from the HMI or program the command #MATERIAL.
Summary of Contents for 8065
