Error solving manual.
CNC 8060
CNC 8065
·127·
(R
EF
: 1709)
3071
'S, M or H functions are not admitted while a gear change process is active'
DETECTION
During execution.
CAUSE
The user has interrupted the program during a gear change. The CNC cannot change
functions S, M or H.
SOLUTION
Go on with the execution until the gear change is completed. Then, interrupt the
program and send the desired functions to the spindle.
3072
'The programmed pitch and spindle S values for G33 exceed the maximum feedrate
allowed'
DETECTION
During execution.
CAUSE
When starting a G33 threading, the CNC has detected that the programmed pitch
and speed result in a feedrate that exceeds the maximum permitted. The maximum
feedrate may be limited by machine parameters or by PLC.
SOLUTION
Check how function G33 has been programmed. To keep the programmed pitch,
modify the programmed speed or, if possible, increase, via PLC, the maximum
feedrate of the channel. Otherwise, check the machine parameters related to the
maximum feedrate of the axes involved in the thread.
3073
'Corner speed limit exceeded'
DETECTION
During execution.
CAUSE
The CNC has exceeded the dynamics of some axis during the transition between two
blocks.
SOLUTION
Contact Fagor.
3074
'Function incompatible with Motion Control'
DETECTION
During execution.
CAUSE
The CNC has tried changing the coordinate system or the coordinate transformation
while a control function is active and parameter IMOVEMACH disabled.
SOLUTION
Disable the motion control functions before changing the coordinate system or the
coordinate transformation.
3075
'Multiple axis deactivate'
DETECTION
During execution.
CAUSE
The axis cannot be moved because it belongs to a multi-axis group and it is
deactivated.
SOLUTION
Activate the axis to be able to move it (PLC mark SWITCH).
3076
'It is not possible get out of MHFS while Retrace is active. Cancel'
DETECTION
During execution.
CAUSE
The user has tried to get out of MHFS mode while the PLC mark RETRACE was
active.
SOLUTION
Cancel the RETRACE mark of the PLC before getting out of the MHFS mode.
3077
'Single-block mode is not admitted in this RETRACE process'
DETECTION
During execution.
CAUSE
In some programs with lots of very small motion blocks, the single-block mode cannot
be used because it may saturate the resources of the system.
SOLUTION
This retrace process does not allow the "single block" function. It is recommended
to deactivate the "single block" function.
3078
'The master spindle of the synchronization does not go into open loop'
DETECTION
During execution.
CAUSE
The user has programmed an open-loop synchronization (OLOOP) for the master
spindle, but it was working in closed loop for another previous synchronization and
will stay in closed loop.
SOLUTION
Leave the spindle in closed loop or cancel the previous synchronization so the spindle
can switch to open loop.
3079
'The master spindle of the synchronization does not go into closed loop'
DETECTION
During execution.
CAUSE
The user has programmed an closed-loop synchronization (CLOOP) for the master
spindle, but it was working in open loop for another previous synchronization and will
change to closed loop.
SOLUTION
In order for the spindle to stay in open loop, program also the second synchronization
in open loop.
Summary of Contents for 8065
