Error solving manual.
CNC 8060
CNC 8065
·138·
(R
EF
: 1709)
3801
'Distance or feedrate in incremental jog equal to zero'
DETECTION
During execution.
CAUSE
The moving feedrate or distance in incremental jog is zero. No jogging feedrate has
been programmed and machine parameter INCJOGFEED is zero or machine
parameter INCJOGDIST is zero.
SOLUTION
Set a new feedrate from JOG mode. Check axis machine parameters INCJOGFEED
and INCJOGDIST.
3802
'Incremental jog feedrate too low'
DETECTION
During execution.
CAUSE
The position increment calculated for a PLC cycle is too small.
SOLUTION
Check axis machine parameters INCJOGFEED and LOOPTIME.
3803
'The handwheel resolution cannot be zero'
DETECTION
While changing handwheel resolution from the operator panel.
CAUSE
The handwheel position selected from the switch or PLC has a zero resolution
associated with it.
SOLUTION
Check axis machine parameter MPGRESOL.
3804
'Handwheel index out of range (switch positions 1-3)'
DETECTION
While changing handwheel resolution.
CAUSE
The PLC has tried to select a handwheel position that is out of the permitted range.
SOLUTION
Check in the PLC program the writing of the (V.)PLC.MPGIDX variable.
3805
'Zero feedrate or distance in incremental jog'
DETECTION
While changing the moving distance or feedrate in incremental jog.
CAUSE
The incremental jog position selected by the switch or by PLC is zero.
SOLUTION
Check axis machine parameters INCJOGDIST and INCJOGFEED.
3806
'Incremental jog feedrate greater than the maximum value'
DETECTION
During execution.
CAUSE
The feedrate set by machine parameter for incremental jog is greater than the
maximum allowed.
SOLUTION
Check machine parameters MAXMANFEED, INCJOGFEED and G00FEED.
3807
'Incremental jog index out of range (switch positions 1-5)'
DETECTION
During execution.
CAUSE
The PLC has tried to select an incremental jog position that is out of the permitted
range.
SOLUTION
Check in the PLC program the writing of the (V.)PLC.INCJOGIDX variable.
3808
'The axis does not exist or is not available'
DETECTION
During execution.
CAUSE
The possible causes are:
• The axis was not in jog mode when quitting that mode.
• The CNC has detected function G101 or G102 for the slave axis of a gantry pair.
SOLUTION
Press reset to exit the jog mode. Functions G101 and G102 must be programmed
for the master axis of the gantry axis.
3809
'Zero spindle speed programmed in G95'
DETECTION
During execution.
CAUSE
The CNC has tried to move an axis in continuous or incremental jog while function
G95 was active and zero speed at the spindle used for synchronization.
SOLUTION
Program a speed for the master spindle of the channel or for the spindle used for
synchronization (SYNC register).
3810
'Handwheel mode not allowed with Hirth axis'
DETECTION
During execution.
CAUSE
THE CNC has tried to select a Hirth axis to move it in handwheel mode.
SOLUTION
A Hirth axis cannot be moved in handwheel mode; it may be moved in continuous
and incremental jog modes.
Summary of Contents for 8065
