Atmel ATSAML22G16A-AUT Manual Download Page 195 | Manualshive

Page: 195 / 1231

background image

–

When the device is in standby sleep mode and the NVM is not accessed. This behavior can
be changed by software by configuring the SLEEPPRM bit group of the CTRLB register in the
NVMCTRL peripheral.

–

When the device is in idle sleep mode and the NVM is not accessed. This behavior can be
changed by software by configuring the SLEEPPRM bit group of the CTRLB register in the
NVMCTRL peripheral.

•

Regulators: by default, in standby sleep mode, the PM analyzes the device activity to use either the
main or the low-power voltage regulator to supply the VDDCORE. Refer to

Regulator Automatic

section for details.

GCLK clocks, regulators and RAM are not affected in idle sleep mode and will operate as normal.

Table 20-3. Regulators, RAMs, and NVM state in Sleep Mode

Sleep Mode

NVM

Regulators

VDDCORE

VDDBU

main

ULP

Active

normal

normal

on

on

on

Idle

on

on

on

on

Standby - case 1

normal

auto

on

on

Standby - case 2

low power

low power

on

on

Standby - case 3

low power

low power

on

on

Standby - case 4

low power

low power

off

on

on

Backup

off

off

off

off

on

OFF

off

off

off

off

off

Note:

1.

RAMs mode by default: STDBYCFG.BBIAS bits are set to their default value.

2.

auto: by default, NVM is in low-power mode if not accessed.

3.

auto: by default, the main voltage regulator is on if GCLK, APBx, or AHBx clock is running during
SleepWalking.

Related Links

RAM Automatic Low Power Mode

Regulator Automatic Low Power Mode

20.6.4. Advanced Features

20.6.4.1. RAM Automatic Low Power Mode

The RAM is by default put in low power mode (back-biased) if the device is in standby sleep mode.

This behavior can be changed by configuring the Back Bias bit groups in the Standby Configuration
register (STDBYCFG.BBIASxx), refer to the table below for details.

Note:

In standby sleep mode, the RAM is put in low-power mode by default. This means that the RAM is

back-biased, and the DMAC cannot access it. The DMAC can only access the RAM when it is not back
biased (PM.STDBYCFG.BBIASxx=0x0).

Atmel SAM L22G / L22J / L22N [DATASHEET]

Atmel-42402E-SAM L22G / L22J / L22N_Datasheet_Complete-07/2016

195

«
...
193
194
195
196
197
...
»

Summary of Contents for ATSAML22G16A-AUT
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ATSAML22G16A-AUT

Brand: Lattice Semiconductor Pages: 30

Brand: Galaxy Control Systems Pages: 5

Compact Comfort VAV12

Brand: SAI HVAC Pages: 16

Brand: Sailor Pages: 1

Brand: Full Gauge Controls Pages: 3

TruPortal TP-ADD-1DIP

Brand: Interlogix Pages: 9

Brand: Apricus Pages: 32

Linear Technology ADI Power DC3017A

Brand: Analog Devices Pages: 12

WFHC 06Z 02 HC RF 24

Brand: Watts Pages: 18

Errata MSP430F6779

Brand: Texas Instruments Pages: 27

Brand: TAC Pages: 76

Brand: OMEGA AIR Pages: 12

Brand: Lennox Pages: 34

Brand: Rohde Pages: 344

Brand: Aurora Scientific Pages: 21

Brand: Clare Controls Pages: 3

Brand: Swegon Pages: 11

Brand: ICP DAS USA Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands