Atmel ATSAML22G16A-AUT Manual Download Page 1096

Page: 1096 / 1231

43.8.2. Control B

Name:

CTRLB

Offset:

0x04

Reset:

0x0000

Property:

PAC Write-Protection, Enable-Protected

Bit

LREN

LRD[3:0]

Access

Reset

Bit

BBEN

BBD[3:0]

Access

Reset

Bit 15 – LREN: Low Resistance Enable

This bit enables/disables the low resistance network.

This bit is not synchronized.

Value

Description

Low resistance network is disabled.

Low resistance network is enabled.

Bits 11:8 – LRD[3:0]: Low Resistance Enable Duration

These bits configure the enable duration of the low resistance network.

Enable duration = (LRD + 1) x period of CLK_SLCD_OSC.

These bits are not synchronized.

Bit 7 – BBEN: Bias Buffer Enable

This bit enables/disables the bias buffer.

This bit is not synchronized.

Value

Description

Bias buffer is disabled.

Bias buffer is enabled.

Bits 3:0 – BBD[3:0]: Bias Buffer Enable Duration

These bits configure the enable duration of the bias buffer.

Enable duration = (BBD + 1) x period of CLK_SLCD_OSC.

These bits are not synchronized.

Atmel SAM L22G / L22J / L22N [DATASHEET]

Atmel-42402E-SAM L22G / L22J / L22N_Datasheet_Complete-07/2016

1096

«
...
1094
1095
1096
1097
1098
...
»

Summary of Contents for ATSAML22G16A-AUT
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ATSAML22G16A-AUT

Reviews:

Related manuals for ATSAML22G16A-AUT

Brands by name

Popular brands

Atmel ATSAML22G16A-AUT, Manual

Search results

Summary of Contents for ATSAML22G16A-AUT

Reviews:

Related manuals for ATSAML22G16A-AUT

Brands by name

Popular brands