Atmel ATSAML22G16A-AUT Manual Download Page 289 | Manualshive

Page: 289 / 1231

background image

the SUPC is reset. See the INTFLAG register for details on how to clear interrupt flags. The SUPC has
one common interrupt request line for all the interrupt sources. The user must read the INTFLAG register
to determine which interrupt condition is present.

Note:

Interrupts must be globally enabled for interrupt requests to be generated.

Related Links

Nested Vector Interrupt Controller

Sleep Mode Controller

on page 191

23.6.7. Synchronization

The prescaler counters that are used to trigger brown-out detections operate asynchronously from the
peripheral bus. As a consequence, the BOD33 Enable bit (BOD33.ENABLE) need synchronization when
written.

The Write-Synchronization of the Enable bit is triggered by writing a '1' to the Enable bit of the BOD33
Control register. The Synchronization Ready bit (STATUS.B33SRDY) in the STATUS register will be
cleared when the Write-Synchronization starts, and set again when the Write-Synchronization is
complete. Writing to the same register while the Write-Synchronization is ongoing (STATUS.B33SRDY is
'0') will generate an error without stalling the APB bus.

Atmel SAM L22G / L22J / L22N [DATASHEET]

Atmel-42402E-SAM L22G / L22J / L22N_Datasheet_Complete-07/2016

289

«
...
287
288
289
290
291
...
»

Summary of Contents for ATSAML22G16A-AUT
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ATSAML22G16A-AUT

Brand: Ubisys Pages: 2

Brand: Acclaim Lighting Pages: 32

Brand: Harsco Industrial Pages: 57

Brand: Eaton Pages: 2

Brand: National Instruments Pages: 40

Brand: National Instruments Pages: 28

Brand: National Instruments Pages: 7

Brand: mikroElektronika Pages: 3

Brand: Window Master Pages: 7

TRIO MPC-165 Series

Brand: Sutter Instrument Pages: 60

Brand: EpiSensor Pages: 37

Brand: Samson Pages: 44

Brand: Hansen Pages: 12

Brand: Srne Pages: 13

Brand: Cruisair Pages: 30

Brand: KELD Pages: 2

Brand: VADDIO Pages: 16

Brand: AMX Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands